I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
We have used nus profile for over a year, and it has worked as expected. Now we added security to the BLE connection, with ble sec connection enabled, it works as expected...
Hello everyone,
I am currently in the process of designing a prototype using the nRF9160 and I use the Nordic-Thingy91 as a reference for some parts. The Thingy91 uses the...
Is there any supporting documentation or information about remote assignment of receivers.
The only reference I have been able to locate is sparse and not backed by anything...
Hi guys,
I'm pretty new in embedded development without using an Arduino. I tried to use the sensor APIs of BMI270 and BMP388 recently, but didn't get it to work.
The...
HI All,
Could you please share the details for the below s on Nordic controller MCU nRF52833-QDAA to receive quotation on BLE_SIG certification,
QDID for Link Layer...
Hi,
I have a custom board running with the nrf52832. To program it I'm using the nrf52DK board with the PCA10040 and the bootloader is based on the one found in examples...
DK : 52840
case :
we make 52840 enter active scan state and know other broadcaster devcice mac,
can we use scan filter policy filter this broadcaster devcice ,and only...
(1) I connected Nordic nRF52810 device to ipad (version: 13.5.1) (ipad uses app for connection). At this time, a pop-up window appears asking if I want to pair the devices...
Good morning. I want to take ADC 12bit/1k sampling input and send uart and bluetooth. uart works fine, but there is a problem with losing data in bluetooth transmission. ...
During testing of various combination of BLE Mesh Provisioning, I found a couple of bugs in dk_prov.c
If you Disable all OOB options for no OOB, it does not work properly...
I'm using nrf_pwr_mgmt_shutdown to shut down the system to wake on interrupt. 17.0.2 SDK and 7.2.0 softdevice. When I step through the code with a debugger, it gets to sd_power_system_off...
My device is powered by an electromagnetic field from the 10 kilovolt line, which cannot deliver much power. When connected to a zigbia network, nrf52840 consumes too much...
I want to receive only 1 byte (Master in Slave out) without sending any bytes using using SPI. However when I monitor the SPI clock it produces 16 clock pulses. Although my...
Hello, How do disable code optimization in SES Nordic Edition when using nRF Connect SDK? I can't find "Options - Code Generation - Optimization Level" as when using nRF5...
Dear Sir,
I am trying to run example with NRF91 DK MQTT simple and I am able to connect with LTE network. as shown in below screenshot.
But as shown in the screen...
