I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I would like to double check with you if 9-pin cortex-M adapter board for Jlink can be used and connected to PPK P21 connector : https://www.segger.com/products/debug...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using internal flash one of the sector with start address of 0xfc000.
We have written...
Hello, we are having a low occurrence issue when attempting to write some data in NVM using fstorage.
We are using a nRF52832 as a BLE peripheral using SDK15.2.0 and SoftDevice...
Nordic colleagues,
We just received our nRF 52840 DK and are attempting to install the nRF Sniffer application to use with Wireshark. We were able to program the DK with...
Are there any plans to expose a raw packet interface for the nrf9160? And ideally forwarded via an async serial port, perhaps as an option for the SLM application? i.e. without...
Hello,
I have a problem of reading GPS options for "NRF_SO_GNSS_POWER_SAVE_MODE"
This is the code:
I always get -1, and errno value 22. This function works for ...
Problems encountered in nrf51822 software development: When burning the program to the microcontroller, I used the Bluetooth serial port service to send the collected adc...
I'm working on a prototype currently using the nRF52840 dongle. I've used the ble_app_blinky as a basic, and added some custom code to it. The goal is to use BLE in the end...
Hello everyone,
My empte memory is displayed as EE instead of FF after i cleared the memory.
I use commandpromt to check memory:
nrfjprog --qspicustominit --memrd...
I am sending a data packet by notification that spans many MTU sizes. So I do a loop over the sd_ble_gatts_hvx(m_connection_handle, &hvx_params) method until I get a BLE_ERROR_NO_TX_PACKETS...
Hello. I'm having an issue with nrfjprog that has been discussed in this forum several times but I can't manage to get it working. I'll link some of mentioned posts at the...
I use AT%XVBAT command as the power query of the device.Now when the voltage is inquired, the return value jumps and the measurement is inaccurate.During this period, there...
I have a design using nRF52832, and I'm hoping to use RAM set before a pin reset is applied. But, at least with a debugger attached, RAM appears to be randomised through a...
