Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
To the kind attention of Nordic team,
About what has been said in https://devzone.nordicsemi.com/f/nordic-q-a/51879/saadc-in-sample-convert , I'd like to know if the blocking...
Dear Member,
I want to call nrf_libuarte_async_rx_free from another file outside main.c
nrf_libuarte_async_rx_free(&libuarte1, (uint8_t *)&GPS.rxTmp, 1);
I got
.....
I was following the article here on programming the nRF52840 Dongle, but am running into issues, and I have other questions as well.
(+) nRF52840 Dongle Programming Tutorial...
2021-02-01 EDBOND Hi Nordic and fellow nrf users
In my project the host cpu is SPI master, Thusthe nrf52 needs to spis slave. Using 2 DK-52 Boards, - nRF5_SDK_17.0.2_d674dde...
Hi,
I am doing some research for the antenna matching of the NRF52832. Now the product specification v1.4 on page 551 states:
"A matching network is needed between the...
How to make the nRF52840 SPI work in 8M with 1.8V supply?
We test the PCA10056 nRF52840 DK board, and find the 8M SPI CLK&DATA wave is very bad. The 8M SPI works fail with...
hi
I tried zigbee tx carrier mode start at 11 channel and tx power = NRF_RADIO_TXPOWER_POS8DBM.
But, When measured with measuring equipment, i got zb tx power -20 ~...
I recived nrf5 SDK V17.0.2
I'm testing with in "nRF5_SDK_17.0.2_d674dde\examples\peripheral\radio_test" folder.
I tried zigbee tx carrier mode start at 11 channel and...
The application I am designing gets a pulse ox measurement from the user, sends it, disconnects, and shuts off. Are there any deleterious side effects of exiting the main...
Is it possible to fill some field when sending advertise message.
We want to change some filed periodicity, so is it possible every time sending the advertise message. ...
Hi,
I still have issue with programming.
I don't understand why i always have trouble with DLL.
I'm able to program with SES, the bootloader and my application. But...
I have a BMD-300 Eval board with the nRF52832 programmed as SPI slave using the SPIS example program. It works, but I cannot figure out how to send a message back to the master...
Hi,
I have done some reverse eng on a nrf24l01+ emitters using spi spy and managed to catch datas using an arduino leonardo + nrf24l01+ using the following register setup...
Hi All,
I have an nrf52833DK and now I want to debug the program.
I am using NCS V1.4.99 and using SES for development. I created a 52833 project, but I used the nrf...
