Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hello, everyone.
I would like to use LSM9DS1, a 9-axis IMU sensor. To test this, an IMU sensor module 'SparkFun 9DoF IMU Breakout - LSM9DS1' was purchased.
This module...
I am working with Zephyr version 2.4 on nRF52840-Dongle for adding ability to scan CODED PHY devices. My host is Raspberry Pi3 with kernel version 5.4.51 v7+, HCI_USB sample...
Hello,
I am trying to run USBD_MSC example using PCA10056 board from SDK15.
It works fine, when creating new file on each button press.
I modified code to create and...
Hello everyone ,
I have question about the difference between periodic message publishing via the module's configuration and publish message by a standard timer.
I notice...
nRF52833 DK i have seen from Images of board that an external antenna will be required(there is a Antenna connector on board). I am wondering if it has built-in antenna or...
Hello,
I am on nrf-sdk v1.3.0 and mwf v1.2.0.
We are updating our product to the above mentioned nrf-sfk version and have noticed that MQTT connection gets stuck after...
Hi,
I enabled flash log backend with NRF_LOG_BACKEND_FLASH_ENABLED set to 1, and NRF_LOG_BACKEND_FLASH_START_PAGE to custom address to keep it as the starting address for...
Hi,
We have successfully created a PCB layout with a PCB antenna following the reference schematic provided by the nrf8001 datasheet. We tested and it is working fine. However...
Hi,
I am trying to interface External Flash (IS25LP064A ) using SPI example in SDK v16. I am able to read the Manufacturer_ID and the device ID from the external flash....
Hi,
Is it possible to somehow read END event register via CPU (not with ppi usage)? If yes, how? I have tried to read value on address from pointer returned from function...
Hi, I am facing an issue my product contains Ble dfu update, I tested my code without enabling DFU and it runs fine ... but after enabling dfu and creating package... I update...
Hello, everyone!
I use SDK v17 and test various functions using App_Timer. The timer function that I want is to turn the LED on for 5 seconds and then turn off after 5...
Hi,
We have been working with a coordinator and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hello all,
I am trying to make use of some Sparkfun libraries for some sensors in my nrF52pca10040.
I am interested on I2C, these libraries use the Arduino library Wire...
Hi everyone,
I am using the PPK to supply 3V to an external device and measure the current consumption.
When I start nrF Connect, connect to the PPK and change the Voltage...