I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Today I am attempting to set up an MQTT connection from a Thread device to an MQTT server on the Internet (for better or for worse, if this is a terrible idea I'm open to...
Hey
Im trying to as low power consumption as possible and for that i have found that sys_poweroff() gives me that.
My problem is that i cannot get a pin state change...
I work on a project where we make a device with a 9160, and our application is build using NCS 1.7.0 and is programmed with MFW 1.3.0. The network our devices connect to is...
I have basically all my code disabled, all I do in main() is get a pointer to the "zephyr_console", suspend it and return.
This gives me an average power consumption of...
Hello,
I try to dfu with mcumgr but I feel like the download speed is a little slow. So I want to increase download speed. I think that mcumgr has the command to set boudrate...
Hello,
We are designing a board with a nrf5340 with a VDD of 1.8V.
The board is very small and it's complex to fit all the components on it.
We are thinking of removing...
Hello,
I was wondering if there is away to perform DFU using SPI without smp protocol or mcumgr from one nRF52840 to another? What I am trying to do is to send a firmware...
Hi,
We are trying to attain power optimization in our project, which uses the nRF5340 board. In our code we have implimented RTOS, BLE for data transfer and are using i2c...
Hi,
I encountered an issue since i upgraded nrfjrpog
My previous version was 10.13.0
And now is 10.24.2.
I have a batch file to program my device and until the upgrade...
We need very fast Wi-Fi transfer rates at times. I have been able to tune the code and Wi-Fi driver settings to get up to 30-35 Mbps which is great. But if I don't throttle...
Hi,
Added a function to the coap_client sample code that executes otInstanceFactoryReset by pressing a button and sets it to factory shipping mode. However, it appears that...
I'm developing a system where I want to connect simultaneously to different BLE and ANT+ sensors. I'm using the nRF5340 DK and I would like to be able to select which sensors...
I have a project that I'm pulling in code from multiple_adv_sets using v2.7.0 and sysbuild.
talks about the opcodes and status being in the spec? https://www.bluetooth...
Hello,
We are designing a board with a npm1300 and a nRF5340. A button is connected to npm1300 SHPHLD.
On short-press, we want the npm1300 to send an interrupt to the...