Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Dear ,
I just want to know about thingy 91 - pca20035 status
1. asset_tracker :nrf9160 SIP works
2. usb / usb_uart_bridge / : nrf52 ?? confusing !
and how about...
Hello Support Team,
Currently NRF52832 is being used for wearable product ,
For NFC Card Emulation Mode whether NFC Front END IC is required ?
or Can go ahead directly...
I designed a prototype using nRF52832 controller. On this prototype I was using the same Flash Controller ATSAM3U2 used on the nRF52DK.
I am bringing up the prototype and...
Hi,
From time to time, we need to send data directly to certain node. There is AF_DataRequest() API in CC2530 to do that. Is there any similar way to implement that kind...
Hi all,
My aim is to " read Four ADC Channels data and sent them to nRF Connect bluetooth app".
For doing this i used "saadc " and " ble_app_uart" examples.
Till now...
In spec "PPK_User_Guide_v2.3.1" ,chapter " 6.6 Measuring current on custom hardware without an nRF5 DK "
I connect PPK to computer as the picture above, micro USB for...
Hi, the thread at https://devzone.nordicsemi.com/f/nordic-q-a/48859/nrf9160-dk-connecting-problems-with-nrf-cloud/211627 has been very useful for me to get past several problems...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
After struggling quite a bit to get network traffic going on nRF9160 DK using NB-IoT, I've contacted our SIM card provider (Com4 in Norway). They are telling me we need to...
Hi, I have run light switch example in SDK 15.2 and SDK for Mesh version 3.1.0 , and it run OK, I can use Configuration Model in Provisioner Node to config 1 Client and 2...
nrfx provides NRFX_SPIM3_NRF52840_ANOMALY_198_WORKAROUND_ENABLED, but this workaround does not work with the SD, and probably in other cases as well.
We use nrfx only, not...
Hi Team,
So far... after going through the Info Center, I see that the same Nordic SoC could be used to do both BLE, Zigbee and 15.4.
In my case, I have a device which...
Hi all,
I am new on this forum looking for help. I programmed nRF51-DK using the ble_proximity example provided by the nRF5 SDK, I'm able to ring the phone by double pressing...
