When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
hello ,
i want to develop a smart home product in which i want to use the indoor positioning using Bluetooth 5.1 Direction finding, i have seen that the " nRF52811 " have...
Hello I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
We have developed...
I am trying to use a Raspberry Pi B+ as Bluetooth to Wifi bridge. But I find that the bluetooth range is very diminished when talking to my Nordic nRF51 and nRF52 devices...
Sir,
I have a question about the connection's power setting of the BLE.
I use the API as the screenshot, but there have a error return. I don't konw the reason, so I...
I am following Getting Started Assistant on Mac platform.
However, I run into an error when I issue: " pip3 install --user -r zephyr/scripts/requirements.txt ".
" ERROR...
Hello,
there’s a section in the NRF9160 specification (11.1) that calls out that VDD_GPIO should be applied after VDD has been applied on power up and VDD_GPIO should be...
Hi,
I am sending firmware image using my DFU master. The image needs to be divided into data objects each of 4096 bytes and then those again into 244 byte BLE packets. So...
Hello,
I'm trying to connect to nrf connect with the nrf9160 DK. I am using an Irish vodafone NB-IOT sim to establish the connection. This sim has an access control list...
Hi,
I have a question regarding a DFU update via BLE. I am using mesh sdk v3.20 and sdk v15.30 with custom hardware (nrf52840).
I have the BLE DFU working as expected...
Hi all,
I am using mesh sdk3.20 and sdk15.30.
I noticed that with the buttonless ble dfu, it is not possible to perform a DFU transfer after the device was provisioned...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
