Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hi, Can I use nRF24LE1-F16Q24-DK without nRFgo Starter Kit? If yes please suggest me programmer to program nRF24LE1 by Keil IDE. by referring documentation I found its support...
Hi
SDK v15.2.0 SD 6.1.1
I have managed to send out "Connectable, Non-Scannable" extended adverts with some AD packets as payload. On a frontline sniffer as per the file...
I am developing a HID keyboard based on an nRF51822.
The firmware source available here:
https://github.com/martonmiklos/ble_keyboard_fw
(It is based on the ble_sdk_app_hids_mouse...
Hello,
i'am trying to control the pwm Idle State Level.
between my Sequence's (1sek) the PIN stays High But i need it low.
I try to set the GPIO Out Register, but...
Hello,
I am working on a simple Bluetooth mesh example setup with the following configurations:
nRF52832 DK: light switch server, subscribed to group 0xC000
nRF52840...
We have a mobile app on iPhone and Android, the NRF52 advertises every 3 seconds. The app can discover the NRF52 quickly but it takes a long time to connect. The iPhone is...
Hi,
I am developing a system that will read from a sensor that uses I2C and then transmit this to a "master" using ANT+ or BTLE (this isn't decided yet)
For the prototyping...
Hello,
Where can I find the pre-built binaries for the below Provisioning options :
1.OOB (Public Key) and Authentication - Input
2.OOB (Public Key) and Authentication...
Hello.
I have an nRF51822 chip and I'm trying to figure out how the whole nRF5 sdk works.
I am using the Segger Embedded Studio.
I downloaded the last nRF5 SDK v15.3...
Hi!
I'm trying to use the AWS-FOTA sample, I flashed the sample onto the board and it connected to the AWS account successfully, but when I try to add the update.bin file...
Hi. The main loop of my app is mostly doing SPI communication to a GPS receiver. I'd like it to do that every second or so and spend the rest of the time in system on but...
Is it possible to configure the ACL to protect the UICR registers?
If so, would this have any impact on the SoftDevice or other nRF52840 peripherals? I.E does the SoftDevice...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
Hi
I am a beginner in the MCU and SoC realm. I was checking the nRF52810 WLCSP33 specs but could not find any mention of the bluetooth range. Is it a standard range for...
