Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
I am trying to get a simple spi setup working. Through the dev zone I found a link to this https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160...
It seems like several people have been able to order nRF52840 WLCSP. I checked all of the Nordic recommended distributors but none of them have stock. Would you suggest distributors...
I am trying the demo from github ( https://github.com/andenore/NordicSnippets/blob/master/examples/i2s_master/main.c ) with nrf52 demo board and when checking the signal on...
I am trying the demo from github ( https://github.com/andenore/NordicSnippets/blob/master/examples/i2s_master/main.c ) with nrf52 demo board and when checking the signal on...
I'm following pc-ble-driver compilation steps.
I could run "vcpkg install asio" and "vcpkg install catch2", but "vcpkg install --head spdlog" fails with error:
C:\dev...
Hello, I am usering nrf52840, now i am testing the current. i found that the current is 40uA in 0dBm while 201uA in 8dBm. maybe it is abnormal in 8dBm, what can i do to check...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi, I am fiddling with this example from the SDK: infocenter.nordicsemi.com/in...cp=5_1_4_3_1_2
In this example, there is a test regarding key derivation as:
As I understand...
I am getting intermittent pickup of advertising packet from a peripheral known to advertise every 2 second. Basically I get ~20 sec gaps where nothing is received.
Below...
I want to use the ble in nrf51822, and I use the example in nrf51_SDK_11.0.0 and softdevice in nrf51_SDK_11.0.0 \s130nrf51201\s130_nrf51_2.0.1_softdevice.hex(thougt the example...
Hello
I am currently looking for the best method to write and read values in the flash. My values are 17 uint16_t arrays with 216 indices per array. I would like to store...
Hello All I am new to this nordic semiconductors. I need information regarding nRF52840 DK boards.
* How to connect two nrF52840 DK(transmitter to receiver) and start advertising...
Hi, I have a SIM800L GSM/GPRS module that I can successfully talk to via the UART on the nRF51.
I can tell it to dial numbers etc and that all works fine.
My problem...
Hi, I'm using app_pwm with 32.768Khz external xtal. the following is my setting in sdk_config.h.
// <0=> RC // <1=> XTAL // <2=> Synth
#ifndef CLOCK_CONFIG_LF_SRC #define...
Hi,
I used sdk 15.2.0 version, I refer to the ATT_MTU Throughput Example to modify the Nordic UART Service (NUS) Application example.
Now I have some questions:
1. How...