When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I am working on matching an antenna to the nrf52832 QFN package. I am looking at the reference design, which has a 30 mil wide trace. I believe that is supposed to be 50 ohms...
I have an application (key fob) that needs to wake up on a button press. Scan and connect to a specific BLE device, then send one byte of data and disconnect and turn off...
Hello, I have a question about using PPI with a SPI transfer.
I’m using a NRF52832 custom board with the Softdevice. I’m reading sensor data every 20ms via TWI and sampling...
Good day!
I purchased the nRF24L01 Evolution Kit, but:
1. The driver and software that comes with the board, only under Windows XP. Are there drivers and software for...
Hi,
I use the server and client from "light_switch DEMO", along with iOS app (nRF Mesh) for setting and pairing. Both ”subscription” & ”publish address” are set as 0xC001...
Hi,
Serialization Function packet format for nRF5 SDK v15.2.0
Am working on serialization where we have already developed code using nRF5 SDK v11.0.0 but now we started...
Hi
I have a problem with receiving / transmitting a packet of characteristics with a descriptor 2902 (CCCD 2902). The principle of operation of my program is that the device...
What will be correct linker script changes for nrf51802 device using soft device ble application
I made changes in RAM start and SIZE. found in open source forum,
MEMORY...
I using 3 nRF52840 DK borads (provisioner,light_switch_client, DFU). I set DFU (DFU example used) as target board and connected it to PC as serial interface. I have provisioned...
Development Software: SES v4.16
Computer Platform: macOS v10.14.4
Hardware: nRF52832QFAAB0
Hello, everyone~
I feel confuse that how to make the Complete Local...
Hello,
We are using nRF52840 and Thread SDK to build a mesh network. At present, we only need to transmit data frames. But, in the near future we would like to transmit...
Hello,
Im trying to boot into a custom bootloader following this documentation .
Under "programming the bootloader" it says you must write the bootloader start address...
I have some question about direction finding in BLE5.1.
1. Does the 52840 DK support nRF52811 Soc? if not, Is there any Development kit support nRF52811?
2. Does the AOA...
I called several distributors but they say they don't have a way of differentiating the revs. Please let me know where to order and if needed...how to order please!
Hello there,
I'd like to send and receive data through NRF Radio's handler. I've been able to configure the handler to receive data. Otherwise, I'm having difficulty on...
