I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hi
Using SD Version 6.1.1 and NRF Version 15.3.0.
Using the following advertising params I can set non-extended advertising
ble_gap_adv_params_t advertisingParameters;...
Hello Nordic support, For long term power profiling of nrf52 hardware, I am using the suggestion given here, that makes use of functions in python script ppk.py: https://devzone...
Hello Nordic Team,
I have an application in development where some bigger files (~20kb) can be downloaded into the device, so they get stored in with the FDS system.
Now...
Hi,
I am using BLE application in NRF52832 board and using NRFConnect app to send custom characteristic service from mobile app to nordic device. But if I am sending a data...
I updated Thingy:52 to firmware version 2.2.0 using the Thingy:52 Android app.
WIth the Thingy:52 running v2.2.0, the WebApp for Thingy:52 can pair with Thingy:52 but it...
Hello Sirs,
We implemented a joint bandwidth test (or speed test) for a radio channel by transmitting notifications.
Parameters set in SDK config:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
I am following the instructions at infocenter.nordicsemi.com/.../nRF52840_PDK_User_Guide_v1.2.pdf to program a pre-compiled example (blinky).
I have two nRF52840-PDK (PC10056...
Hi, im designing a beacon based on nrf52832, but i have a question about RF section, i´m using 2450AT18B100E chip antenna, and to match it with the nrf52 i'm following the...
Hi,
Trying to investigate eddystone protocol. After compiling and uploading ble_app_eddystone example I see Eddystone BLE device in non-connectable mode.
But after pressing...
I am using NRF52840 DevKit on Ubuntu 18.04 (bionic). I have successfully compiled pc-ble-driver and hex connectivity/softdevice.
I have now download pc-ble-driver-py and...
Hi,
We develop a GPS tracking device.
Development kit shows two type antenna, an external antenna(With connector) and onboard antenna for GPS and LTE.
We won't use an...
Hi, I am using nRF52832 with sensor, nfc and Softdevice S132 v3.0.0 to advertising packets .The sensor is interfaced with nrf52832 using twi interface. I have referred examples...
