Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello. I have a breakout board (SMARTMP3 VS1053) and it has also a slot for memory card, so I connect the wires (SCK, MOSI, MISO and CS) to my nrf52832, but it can't see the...
What is the recommended way to protect characteristic value from modification while it is being read by a client?
I have a test application with 500-byte long characteristic...
Dear Team,
is there a tutorial on how to start from scratch a project for zephyr nrf91? With all configurations and flags...
That would be great!
Thanks & cheer
O...
Hello,
We're trying to create a custom bootloader from scratch and we're struggling with a weird behavior. This is for the nRF52840 and the bootloader doesn't use the softdevice...
The SDK version is 15.0.0, SD 132, single peripheral conection.
the configuration:
this is how i request the timeouts:
With the timeouts of about 50ms and less, the...
Hi guys,
I tried to modify "configs.c" or ".config", modified CONFIG_GPS_SIM_TRIGGER_TIMER_MSEC = from 2000 to 10000 .
But the device still sends GPS data every 2 seconds...
Hi there
I have a design in production using Gazell at 250kbs on a NRF51822
I would like to update the design using a nRF52840 but it doesn't support the data rate that...
Hi,
We are looking for a consultant to help us port our product's ( https://www.ncase.io ) firmware from Simblee to the Nordic nRF51822 or nRF52832. Experience with Nordic...
Dears:
I test the uart dfu by examples\dfu\secure_bootloader\pca10056_uart
After I enter command like below：
nrfutil dfu serial -pkg Sena_app_uart_s140.zip -p COM5 ...
My project is Obj-C , and “ pod 'iOSDFULibrary' ” in my Podfile.
It worked fine until I upgraded Xcode to 10.2. There are some errors(about 100) occurred during project...
Hi all
I am doing multiprotocal from sdk15.3 and I am trying to add nrf_gzp.c, nrf_gzp_host.c, and nrf_gzp_host_nrf5x.c in to the project
after compile successfully and...
I was wondering, is it possible to suspend/resume flash operation in nRF52840 (internal flash)? Like flash erase suspend, and also flash write suspend/resume?
Thank you...
Hi,
Might be a silly question,
but is there a gattc equivalent of the "BLE_GATTS_EVT_HVN_TX_COMPLETE", ie a similar/equivalent event that gets generated when a central...
Hey, I am working on the proximity application on nrf51 DK. How can I get the bsp_event_handler to get triggered on a button multi press (such as pressing button 1 twice rapidly...
Hi,
Do you have support for mobility in Cat-M on your nRF9160? This is usually done in RRC connected, but i'm wondering if you are able to support it in eDRX as well?...
