Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello,
My device has GATT data attributes configured to have BLE_GATTS_VLOC_USER so the data are in application stack. In this way, the softdevice has direct access to the...
I've been trying to use the Adafruit nRF52 library ( github.com/.../Adafruit_nRF52_Arduino) and the Arduino IDE to program a nrf52832 using my nrf52840 DK. However, I keep...
Dear Sir,
I wanted to make the peripheral connect to a predefined central device. Here I am using an android phone ( with nRFConnect installed in it) as the central device...
Hi,
I Used nRF52832-CIAA-R in my ongoing product development.
I need two UART and one I configured PIN(P0.6 and P0.8) for GSM.
Can I use any GPIO pin as a UART for GPS...
Hi,
when debugging nRF52 chips, currently using nRF52840-DK with arm-none-eabi-gdb (version 8.2.50.20181213-git), is the use of 'commands' supported?
Trying to see some...
I am using nRF51422 with the SDK 11. I am using the proximity application to measure the battery service. By default, the device uses VDD as its ADC input. I would like to...
Hi
We are using the version 2.0.1 soft device and it consumes 8kb RAM. We have a challenge with RAM on our device so we're looking for ways to make more RAM available for...
Using https://github.com/NordicSemiconductor/pc-ble-driver ( abce7974fe983c23930d362b1769e51c8fa13cbf) .
Just followed the instruction and compiled hex/sd_api_v6/connectivity_...
Hello,
I have a basic queries on BLE.
"Characteristic Properties" of "Characteristic Declaration" with UUID 0x2803 has Read, Write, Notify and Indicate. At the same...
Hi
Can I think so,if subscription address is identical in multiple nodes,then they are a group?
If so:
the light_1&light_2 OnOff Server Model subscription address is...
hi,
I had the board run the following code to connect it to the cellular tower:
#include <zephyr.h> #include <stdio.h> #include <string.h> #include <lte_lc.h>
void main...
I tried to advertising eddy stone beacon from getting serial UART data. i merged 2 codes in ble_app_eddystone and uart code but one error become like
..\..\..\..\..\..\components...
Hello dear Nordic Developer and Hobbyists,
first of all I would like to thank the developer team for the nice mesh demo. It functioned well and explicates the concepts of...
Hi,
I am not getting any response from the previous ticket. Did it get accidentally closed?
Case ID: 225033
Can please someone look at it? We are in urgent need...
