Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
When static authentication is used, it is my understanding that both the provisioner and the privisionee have a static preprogrammed key. The SDK says:
"The application...
Hi, starting from the demos on the devboard, I want to make a custom pcb work now. For that, I do not need UART/logging functions, which will otherwise cost me current consumption...
I use SDK15 and S132. I have examples\dfu\secure_bootloader\pca10040_ble loaded in my board. I can see it advertising when there is not valid app loaded.
Also, my app with...
Hello Nordic Team
I am working on zigBee project. I see there is uart example available in SDK which works BLE + end point. Is there any example available which works on...
Hi all!
I found solution for Xiaomi zigbee smart home sensors (gerkon, water sensor, pir motion, and other...) based on CC2530 zigbee shepherd and Trust Center Link Key...
I am doing a project with nRF24L01+ but i found out this is not certified chip to FCC. Is any other RF that is certified that i can replaced this RF24?
Hello,
I am creating a read-only characteristic with sd_ble_gatts_characteristic_add (specifically, characteristic_add). The value is 31 bytes.
On a Read Request, it is...
Hello
I would like to send my sensor data to a mobile application using BLE SDK 15. Someone suggested me to go through the BLE NUS SERVICE example which was a good one....
Hi,
I am new to Nordic development environment.
I am compiling the some code developed by vendor for NRF5 SDK 12.2.0
I am getting errors such as
Error1 snippet
...
Dear Colleagues,
I could use some help or ideas. I’m working on the link layer encryption of an open source Bluetooth stack. It starts to work! But, now I have the effect...
Using softdevice 6.1.0 and SDK 15.2:
Is it safe to use NRF_UICR->CUSTOMER[0] through CUSTOMER[5] for storing serial numbers?
It seems through in previous versions of SDK...
Hi All,
I have implemented the code for MASTER serial DFU in ST micro controller. which can send the app .bin file. I'm using 57600 baud and disable the flow control....
Hello,
I am using 15.2.0 SDK and 3.1.0 Mesh SDK.
I was trying to control two LED's on the nRF52DK using two generic level server models. I made following changes to the...
Hello. I got an nRF9160 DK with an iBasis eSIM that was already registered on an nRF Cloud account. Is it possible move the already activated eSIM to my Cloud account? I tried...
