Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Dear Nordic Semiconductor Team,
this is the same question as in https://devzone.nordicsemi.com/f/nordic-q-a/40957/att_read_by_type-when-bonded
i accidentaly closed it...
Hi,
I have the exact same issue as mentioned in the below case -
Ticket - LE Data Packet Length Extension does't work
But as this was 2 years ago, I wanted to know if...
Hi Earlier this week I got a mailshot from Nordic with the subject "Nordic Semiconductor’s nRF52840 System-on-Chip is now one of the first chips supporting Bluetooth LE with...
I have used the cli module in SDK 15.0.0 to create a test interface for a API I have built over UART. It works problem free when typing commands by hand but when automating...
Hi,
Look the nrf_mesh_rx_metadata_t definition:
typedef struct { nrf_mesh_rx_source_t source; /**< Source of the received packet. */ union { /** Scanner packet metadata...
Hi,
I'm eveluating the mesh SDK (with segger studio) for some days now and I can not stand that I still can't figure out what the examples for BLE mesh can and can't do...
Hi,
I'm in the middle of developing a software that runs on nRF52840 and scans for BLE devices all of the time, then quickly connects to each and every one as fast as possible...
We're using a host PC to write factory calibration data to an nrf52 running SDK14.0.0 and S132. We're using a serial port, 115200 8N1, without hardware handshaking. The SD...
Hello,
very simple question:
each time i click on the link from the following page, I get an ACCESS DENIED error
infocenter.nordicsemi.com/index.jsp
I know that...
I made some changes in mesh light_switch_client example code and tried to build it in SES, it passed compiling, but stucked at linking:
Building ‘light_switch_client_nrf52832_xxAA_s132_6...
hi..
i merged the two programs twi sensor and uart ... successfully complied
but while debugging i am getting this error
while (m_xfer_done == false)
lm75_mode();...
Hello all,
I have a question about the SAADC of nRF52832.
Now I use the SAADC to measure the some external sensor voltage and the internal VDD voltage.
The sensor connection...
Hello, Excuse me! I used the LFRC,the calibration interval of which is 8s, in my application on NRF52832. In order to measure the power consumption,I want to know the duartion...
Hi,
As well know, nRF52832 can use "16Mhz base-clock to output PWM signal, and it is very simple to create 4Mhz, 2Mhz, 1MHz signal output,
But, If I want to output a...
