Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Dear Nordic
Q1.
We tried new nrf9151 IC at custom board.
IC version: nrf9151 AEA (Engineering B)
Firmware: ncs2.7.0 Serial LTE modem application + mfw_nrf91x1_2.0...
hi,
When verifying the modem upgrade, if the network type is set to support both Cat-M and NB (AT%XSYSTEMMODE=1,1,0,0), the actual network that connects is NB, and the modem...
I have 3 nrf boards connected. 2x nrf52832 and 1x nrf5340.
esb_tx is running on nrf52832(682782977) esb_rx is running on nrf52832(682497942) & nrf5340(1050025410)
west...
Hello
I have a custom nrf52840 board with an external 1MB NOR flash
The app uses MCUboot for DFU
I know I can define the external flash in the pm_static.yml for the...
We are currently working with the nRF52832 Development Kit and are aiming to interface an ISO15693 NFC reader using the PN7150 NFC module. We intend to communicate with the...
Are there any serial commands that I can use to control some the functionalities of the board. My task is to use the dk with a windows app (UWP, C#), I want to start stop...
I tested it on the lzma example (ncs\v2.8.0\nrf\tests\subsys\nrf_compress\decompression\lzma),on the Cmakelist.txt code
generate_inc_file_for_target(
app
${ZEPHYR_NRFXLIB_MODULE_DIR...
We have a production system running a modified asset_tracker_v2. Things are basically running fine but there is question with downlink and FOTA operations. We publish a JSON...
I am trying to get mcuboot working on a custom board. on version 2.7.0 sdk, But the board is not found.
I have simplified it to a minimal version like so (my folder can...
I am evaluating external flash on nRF5340DK. When I'm doing appcore DFU from external flash so that mcuboot_secondary and settings_storage are located on external flash, everything...
Hello!
I am returning to software development for a BLE Mesh project on the NRF52840 after being focused on the hardware development for several months. I see that NCS is...
Hello
I am evaluating Wi-Fi location using the nRF7000 and nRF9160.
For the initial test, I used the nRF7002 Expansion Board. I soldered wires to it and connected them...
What would be the certification cost for developing small volume Zigbee or Matter+Thread applications using nRF modules and nRF Connect SDK? Is this eligible to certify via...
Hi experts,
I followed the instructions the Readme file described. It almost works well. But I still found two issues:
the Startup time is too long when pressing the...
