I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I'm using Matter SDK v2.7.0, when I build example light_switch for Board: nrf7002dk_nrf5340_cpuapp with Configuration: prj.conf, I get errors as below:
/opt/nordic...
I have nrf9160 with w5500 ethernet module. I am successfully able to get IP address and connect to mqtt broker created locally on my network. Now I was trying to connect to...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.7.0 SDK: v2.7.0
I have successfully deployed and tested projects that run normally, but when I...
Hi, Iam trying to run c++ code on nrf52840. I got working C code, so i try only change .c to .cpp. I got some errors but most of them are solvable by putting libraries(.h...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
I have successfully managed to incorporate the hard-float build of the library for the nrf52840 into my bare-metal application ( custom hardware with an nrf52840) and have...
LED5 is blinking very fast. no appearance on computer at all. nrfjprog --recover not reconvering, Tried another PC, another cable and no response at all.
I am trying to read the WHO AM I register of an ICM20948 over SPI with nRF52832, but I am getting incorrect values.
I have tried different SPI modes, but none of them work...
Using Zephyr (cf2149caf2) / nrfSDKConnect on a nrf5340DK board.
I need to know how to get a direct stack trace (with file/line numbers if possible for a debug build).
...
Hello Nordic.
I used nrf52832 and nrf52840 by nrf sdk.
But I need to develop nrf5340 now, and I understand I have to use ncs to develop firmware for nrf5340.
I have...
Dear Nordic Community,
I am trying to implement a porting of micro-ROS framework on the nRF52840 chip. As stated in their tutorial , the framework is compatible with the...
Hi,
I have been testing the CAF click detector module and I find that any event callback after the click event takes almost 1000ms. That is the time between the actual click...
Hello,
I am developing a Door Lock Matter application using the nRF5340 + AT25XE321D (32Mb SPI-NOR External flash). I am having problems with getting my Matter application...
Hi, I have a nRF5340 Development Kit. I want to add a large amount of assembly code from a previous Cortex M4 project (from PSoC Creator 4.2). Project has *.s files and *...
Device Manager App now shows app_update.bin as an Invalid Image file. On a previous version of the app (pre-2.0.0) this worked. What changes do I need to make to my prj.conf...
