Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Dear expert.
one of my clients manufactures medical devices.
as you may know, medical devices need to special certification depending on the country, such as North America...
Hoping someone can point me towards some guidance on how to properly enable, configure, and build mbedTLS options on the nrf52840.
I'm currently using Zephyr 3.6, with the...
Hi,
I developing an Hearing aid accessory with nrf5340 audio and STM32.
I do not have external flash so I need to use the nrf5340 internal flash.
I'm using the 2.5.0...
Dear Nordic, Could you please advise how to interpret the version in this context? The modem firmware v2.X - is it the version that does not exist right now? If yes, when...
Hi everyone,
I'm working on a project where I have four sensors connected to my chip via two SPI buses ( 2 on each with 4 CS). My goal is to read data from these sensors...
I am using an nrf528232 based BLE module, the Taiyo Yuden EYSHSNZWZ: https://www.digikey.com/en/products/detail/kaga-fei-america-inc/EYSHSNZWZ/7104534
Running BLE and uart...
Hello,
I have recently attempted to port over to the latest v2.7.0 of the SDK by following the steps in the latest getting started guide for the L15. I have been able to...
There is this post from three years ago here that mentioned LLPM isn't supported on nRF5340. The answers had mentioned some issues with LLPM on the network core & that the...
NCS v2.6.0, NRF5340dk
I'm trying to configure a project that uses mcuboot with direct XIP with the external QSPI flash. I've been looking at examples in
ncs/v2.6.0/nrf...
Hi! We use Npm1100 SHPACT on GPIO and want to ask connect SHPHLD directly to VBAT.
The spec has 100kOhm resistor between SHPACT and VBAT.
However, we don't use the button...
HI
softdvice : s132
SDK version : nRF5_SDK_17.1.0_ddde560
I am using the nrf_delay_us() function. The product I am using now controls the gpio in us units. Since it...
Hi,
In NCS 2.0, the ability to add a custom child image was added. This works fine but as soon as you include the mcuboot child image, the order of the child image builds...
Hello folks!
Today, I have what I hope is a really easy fix that I just can't find the answer to.
I would like to transition from using the nRF Connect extension "build...
