Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I'm implementing a device based on the NRF52840 Dongle and the hids keyboard example. The basic functionality work, so that I can send pressed keys to a connected...
Hi,
I am trying to implement a ble module in a fall detection application. I added a ble_service based on the BLE fundamentals course lesson 3, which works just fine alone...
Description:
Hello,
I want to measure the distance between two BLE devices with high accuracy . I have already tried using nRF52840 modules , but the results are not very...
Hello,
I'm trying to detect a UART_ERROR_BREAK on an USB ACM CDC interface of the nRF5340 using NCS2.7.
The returned error code is always 0xffffffa8. How do I clear...
Hi
I have a simple application which is comprised of a notification from peripheral to central , and a write without reponse from Central to peripheral.
In windows every...
Greetings,
We are using a nrf54L15 and trying to use the GRTC Clock output functionality as described in 8.10.4 of the datasheet.
We need the most accurate clock output...
In the next step, I compiled the “Serial LTE Modem” firmware example from the examples folder and flashed it onto the nrf9160DK.
The “Serial LTE Modem” application works...
Hi,
I use the nRF9160dk and I want to use nRF9160's internal flash which has 1MB flash to store a few data. But I cannot find any guideline about using nRF9160's internal...
Good evening, I have recently purchased an nRF52 development kit which I would like to use for my project. Currenty, I would like to provision external devices using this...
Hello, I have a custom board that was designed for me, but based off of the Acconeer XM126. It is very similar with a few minor differences. The person who designed it has...
I'm developing based on the Nordic Academy example here, but I noticed that when transmitting a large amount of data, something is limiting the amount sent by the NRF52832...
Hi,
It seems that CONFIG_IEEE802154_NRF5_UICR_EUI64_ENABLE is not supported on NRF54l15.
Where should be the custom vendor EUI64 value stored?
Only the FICR?
Thanks...
Hello, I recently installed nrf sdk but I have trouble getting through getting started phase. I'm using ubuntu 24.04 and created workspace environment using CLI. Below is...
Hi I'm encountering an error while building Lesson 8, Exercise 1, Step 3 using the nrf7002dk/nrf5340/cpuapp target board. Below is the error message I received:
The same...
Hi, I have a BLE device in Observer role - it will constantly scan for Broadcasters broadcasting our unique UUID and put these scanned devices into a Ring Buffer.
The reason...
