Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Tagging Ø yving !
Hello everyone and thanks to the Nordic team for a nice day in Stockholm.
Since the single cell tower localisation was very good compared to GPS...
Hello everyone,
I'm using Gateway (serial example) and send packet "Heartbeat Get" to Devices (Light Switch Server Example )to check alive of devices. But when check alive...
What API could be used to send out ZDO Device announce, when router (zr) or end device joins network ?
Is there any sample code could be referenced?
Thanks,
Robert
Hi!
Three or four months ago I create a ble mesh with 6 nrf52840 Dongles. Now I want to reset all Dongles in order to create a new ble mesh with a different functionnality...
I changed seqValues variable of the following function from 0x8000 to 0x0010. But I can't see LED light darkening. How to dim LED lights by nRF52832 PWM?
static void _ledPwmConfig...
Hello,
I just observed some strange/interesting behaviour. On one of our products there is a green LED connected to Pin 3 of GPIO port 0 on the nRF5340. When I connect the...
Hi everyone, I'm developing a program with the NCS 1.8 using NRF52840 and I want to use the SPI, the fact is that I've to connect my device to those pins
And as you can...
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805.
My application code uses 150 kb Flash(Out 192 kb) . I want to develop...
Hello, I have a question regarding to the DTM;
Is there a way to count the number of test packet transmissions or set the number of test packet transmissions in the direct...
Hi,
We are using the latest ncs release (2.0.2) on a nRF52840 integrating Matter. When looking at the sample apps (e.g. light switch example), the RAM usage for the Matter...
I would like to using nRF52832 EasyDMA for reading and writing to and from the RAM for peripherals (E.g.NOR flash, Analog front-end (AFE), etc.). Could you suggestion example...
Hi,
Greetings!
We are trying to understand how we can send battery voltage to mobile application from nRF52832 based battery operated device.
Please note that we are...
I have tried to connect my NRF 5340 board with BLE application the last few days but had no success. I already tried other solutions like disabling the MSD via the J-Link...
