Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi
I am using app_timer_cnt_get() like MIllis()
uint32_t millis() { uint32_t milli; milli = app_timer_cnt_get() /32.768; return milli; }
but when i connect the nrf52840...
Hello ,
i have successfully compile and run 'binky' and 'Hello_words ' sample code using segger .Now i want to test Uart communication with nrf9160 . (want to send string...
Hi,
we are following below link for DFU example i.e. serial dfu on nRF52833. we are not able to install mcumgr in windows . are we missing anything here. kindly help us...
I'm testing an implementation of the serial UART bootloader for DFU. Firmware update using nrfutil works fine, using a serial-USB dongle, The only issue I'm seeing is that...
Hi DevZone,
I have recently updated:
nRF5 SDK to 17.1.0 from 15.3.0
S140 to 7.2.0 from 6.1.1
SES to v6.20a from 4.16
The SoftDevice now fails to initialize when...
hi support team,
in ncs llpm example, we tested it and find out one problem, why 4bytes of timer data would spend more than 1ms? please see picture 1.
further more,
...
I testing asset_trcker_v2 and want to add new custom event module. I have few doubts and queries:
1. There is event_handler function in each module as well in main fuction...
Hi,
I am working on the nrf5340 with zephyr (NCS 1.7.1), I need to monitor the voltage of the battery, in the beginning, I used the ADC API of zephyr, and it works well...
Currently I have a 52840 peripheral running peer manager. We bond/peer with it using a passkey system from an mobile phone central. It works great.
SDK is 1702 nrf5.
What...
I wanted to confirm that on the nRF9160, it is acceptable to tie the VDD and VDD_GPIO pins to the same 3.3V rail and bring them up together. The VDD_GPIO rail will not be...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard
I want to add UART implementation....
Hi everyone!!! I need help with our new version of HW after validating the previous one that works.
I read some similar posts related to the GPRETREG for HOLD a GPIO while...
Hi Nordic,
We have a design where we'd like to share the 2.4 GHz antenna between WiFi and BLE.
Therefore, we need to power and configure the RF switch accordingly, before...
Hi,
currently I am using nRF52811 in one product with BLE functionality. Now I would like to use the same MCU in other product where BLE is not needed. In this case I would...
