Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I understand that Attribute protocol supports commands, requests, responses, notifications and indications.
Can you please tell me if those packets are sent with the...
Hi,
I'm new to nRF52840 Dongle development.
We use some nRF52840 Dongles (packed in a machine) with pc-ble-driver-py for transferring data through BLE.
I can not share...
Hi,
I'm using the flashlog on my nRF52840 to log events. I have an external RTC which I read when logging each event in order to timestamp the event. My RTC code writes...
I am trying to set up a project that uses MCUBoot and puts the secondary slot into QSPI External Flash. I'm using NCS 1.7.1 with VS Code. I've followed numerous posts on these...
I am currently evaluating the differences between nRF52811 and nRF52810. I am still using the nRF5 SDK.
One difference is in the nRFInitialize function in the startup code...
Hello,
In my application (using sdk 16.0.0) I have a bootloader that allows to upload a new firmware through either BLE or UART. The Bootloader is initialized as usual:...
Hi All!
I have a problem running simple PWM output on NRF5340 board. I have a following code:
Now what i'm trying to achieve is to get 50% of duty cycle with frequency...
Hi there,
This should be straight forward but has me stumped. I'm trying to add BLE to my CAF based application and can't do and recreated the same problem with the samples...
Hello, I have a two part question with regard to SPIS setup time when exiting low power mode on an nRF52840.
We are using the SPIS peripheral on an nRF52840. General guidance...
Hello,
I am currently integrating the Wiznet5500 drivers into a VSCode project, but I am stuck on where to include these custom modules.
In the previous version in SES...
Hi，
I have a problem about CAF leds modules. I submit a led event to turn on led for 3600ms and turn off led for 500ms, but it work inversely in fact.
I find that leds...
SD140
Part nrf52833
Application: Central App that connects to 1 to 16 different peripherals. One at a time.
Problem: 1/10th of the time, I get a disconnect reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED...
I keep getting a hard fault when calling spm_request_random_number()
I'm following the secure_services sample provided in the SDK, and the secure_services header file...
Hi, I am using the nrf52 Thread v4.1.0 SDK for development
I am using ADA4333
there pin 6 is used for Gate control but
in CLI pin 6 is used as uart tx
and it is hard...
I found the following problem with Programmer v2.0.1, using either a Nordic DK or a Segger J-Trace as the programming device (on Mac OS 11.6, and with nRF Connect 3.9.1):...
