Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi Dev team,
I am using the Thingy91 for my development project. I have noticed 1 peculiar issue and wanted to ask for suggestions regarding it.
I had deployed a Thingy91...
Hello there,
I am that newby in the vs code dev environnement. I use the XM122 from acconeer to perform radar measurement. The soft provide by Acconeer compiles and works...
Dear Community;
I am trying to port this code that was made for an nrf52 to an nRF9160. I have a 4.99K pull-up resistor between the data line and VCC.
This is my ds18b20...
Hi, Is it possible to increase the size of the buffer for the UART IRQ RX function such that it receives more than 8 bytes at each interrupt? Currently I am trying to send...
Hello everyone,
I'm reaching out to touch base on the current support status on the latest software (MFW v1.3.1 and NCS v1.7.1) for CoAP over UDP (DTLS) for using as a main...
Hi,
I have a circuit with an I2C peripheral on a separate power switch. There is excessive power consumption (about 50µA extra) due to leakage after TWIM is disabled and...
Hi,
I am using a nRF9160-SICA-B1 and sometimes will see debug output that looks like this in Tera Term:
Glitch example:
Good example:
Basically it appears like...
Hi everybody,
I'd like to perform serial DFU on my nRF52832/nRF52840 based devices, using an external master MCU. Is there any reference C code for the master MCU? In this...
Hello. I am new to Zephyr. I cann't debug Hello_world sample. As i understand it always reboots and does not go to main.
I am trying to use VS Code and nRF Connect SDK ...
NRF Connect shows no device available.
usb interface MCU which embeds a j link is not detected by windows.
LED5 is blinking.
I have an external jlink to try to recover...
I had a project set up and working with my nrf52840 dev kit. It was using the 1.7.0 SDK and was based on the zephyr hello world sample. Today when I open VS Code, the project...
Hi,
On Segger Embedded Studio when you debug you also get the RTT console displayed at the same time. Is this possible on your VS code implementation? At the moment I can...
I'm trying to add 802.15.4 driver into my project (to implement an proprietary protocol).
The wireless_uart sample is very helpful and I got it up and running.
However...
I can find some other topics about this:
Like this one:
https://devzone.nordicsemi.com/f/nordic-q-a/43370/nrf_log_info-and-printf-does-not-work
or this article:
https...
