I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I have a mesh provisioner with the provisioner example in the mesh sdk. When I try to provision a device that is next to the provisioner, all works.
But when I try...
I want to send sensor data using sensor_server_status_publish function, however struggling with data marshalling. I get unknown property ID or no data at all displayed in...
Hello
I am using sdk v17 and nrf52dk and implementing sensor encryption(AES CTR mode) and simple nus service. After reading the sensor to saadc, I want to encrypt and transmit...
Thanks in advanced. I'm using nrf52832 with nRF5_SDK_17.0.2. I try to measure adc time consuming as below:
I find when timer sample rate is 500ms, then adc time consuming...
Hi:
I am doing a project which will use both PDM interface and bluetooth transreceiver, PDM interface is used to receive audio data from a MEMS microphone and Bluetooth...
We have a design that uses a simple custom board with an NRF52832 chip, button, accelerometer and onboard battery. For many phones, the operation is quite stable - we connect...
Hello all:
I've developed an nRF52810 application based on the UART example, but when I include buttonless DFU support to my application, it doesn't work. I'm using SDK...
Hi,
now I had achived the function to communication using the esb in nrf52832 that one to one,but I need to achive multi tx device to one.
if there not doc for me to achive...
Hi
Strange that there is no example for such popular code which will allow changing the iBeacon setting parameters (like: name, power, interval etc). with a smartphone application...
Hi everyone,
I'm trying since a few days to connect the Thingy 91 to the network with any result at all.
This is my configuration:
Modem firmware: V 1.3.0
Application...
Hi,
Am trying to store the data fetched through ble scanning to the flash memory of the nrf52840 DK. So I have been making use fo the flash_storage example in the SDK/examples...
Hello,
Our Peripheral server application regularly uses a stream of notifications to transmit data to a Central client. We have a rare error in which sd_ble_gatts_hvx returns...
app time loop update 200 byte data use fds by 10s ,then after many time error happened, update_user_flash is update API, write_drop_record IS loop write API in app time, ...
When running in High Voltage mode, it specifies a maximum of 7mA of external power draw on the Vdd output. It also specifies the voltage accuracy of -10%/+5%. This is a very...
