I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I just cloned the latest zephyr from github and tried littlefs. However, the SPI pins have no traffic and CS line stays unchanged.
Is there something I forgot, since...
Hi, i'm working with NRF51822, and i saw on reference manual that micro enter in the SYSTEM OFF mode. The problem is i dont want the micro enter on this mode.
I make de...
Hi,
I'm working on a project using the gazelle protocol with the gazelle pairing library. Due to the fact that I use the GNU GCC compiler, I created a Makefile from the...
Dear Nordic team,
We have designed custom boards with nrf52840 chip. We observed that in one of the boards the application is not running until the swd pins of the custom...
Hi,
We are using laird BLE653u BLE module in our application. This module has nRF52833 BLE SOC. We have ST Link V2 as a programmer tool. We want to use SWD protocol for...
I have a project using NRF52840 as master in BLE central to scan BLE device.
I found all example will connect device automatically when device found
I would like to change...
Forgive me if this is already discussed somewhere - I'm fairly certain it must have been - but I can't seem to find what I'm looking for. My client's project uses a higher...
Hi,All:
As the topic,which address is the mbr jumping to bootloader by ?0x10000ff8 or 0x10001014? and how to feed the mbr para register 0x10000ffc and the 0x10001018?
Hello,
I need to use the more accurate HFXO for a very short interval to time incoming interrupts (approx 1/50 second every 15 mins)
The processor sleeps idle for the...
Dear DevZone,
I am trying to configure the SAADC on my custom nRF52840 board.
I would like to use it in blocking mode together with oversample 16x and burst enabled...
Why is SES throwing an "Illegal value 0x21009168 written to register 66 (MSP_NS) ignored" message after "Download successful" when programming nRF5340's network core with...
Hello everyone,
I have questions concerning direct advertising. I have read this and other posts from several years ago which provided some useful information.
devzone...
Hello,
at the moment I am trying to get the NRF9160 Icarus Board to communicate with an ESP8266 Board within serial modem mode. I just need to send some AT commands through...
I am trying to install nRF Connect SDK v1.6.0. For some reason the download speed is extremely slow, and even fails without the ability to resume automatically. On two occasions...
