hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi!
In our current project, we have started to use the Connect SDK.
We have a an application CPU with a modem running our main software and uses the nRF52833 for local...
Hi, I am trying to achieve the lowest current consumption possible on the nRF9160-DK, which should be about 1.4 uA in modem shut down state. Unfortunately, my best result...
Hi all, I want to form a thread network.
I have BorderRouter [Raspberry pi 3B flashed with Nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design] and is up and running...
Hello.
This issue was tested with nRF5 SDK v17.0.2.
There are steps to reproduce :
sdk_config.h should not be included in nrfx_clock.h. It's a default template by...
Hello,
I am looking for some help solving a peculiar issue with eddystone beacons, the nRF52805, and some cheaper Samsung android phones.
System Description: - I am using...
Hello,
I have been running this program without any problem then I added some code to read and write to flash using NVS when the error shown below appeared.
I am running...
I have been using the Toolbox to load zip files to a device. Now the toolbox uploads a file and 'say it is complete', but the file status in the menu window say file not loaded...
Hi forum,
I am working on nrf52832,using sdk15.0.0.
I referred TWI_sensor example as reference for sesnor interfacing. Individual sensor works when i trired to integrate...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
Hi Nordic team, I'm working with nRF52840 PCA10056 , base on Thread_Zigbee_ v4.1.0 , and light_control example. I modifed, try to add temp_measurement ZCL in all light_bulb...
Hi ,
My environment:
nrf5340 dk board
nrf connect sdk
segger studio IDE
.
I want to test spi loop back without any connections.
I don't want to connect any...
Hello, zephyr pwm driver documentation and samples , shows clearly how to generate a PWM output using nrf52840 dk. However, we need to synchronize the PWM output to an input...
Hello, how can we configure the counter in an nrfx52840 dev board to count pulses on an input pin in zephyr? There is a counter driver in zephyr, but there doesn't seem to...
What I'm trying to do, is probably very simple. I hope.
In the following code which works fine.
I want to scan not using Coded PHY
Then change back to using Coded PHY...
