Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi Nordic:
I know mesh LPN can receive messages from it's friend node, that means when any other nodes send messages to LPN unicast address, LPN's friend node will buffer...
I have developed hardware utilizing an nRF52832 and am developing a bootloader for the system. I have had success following two tutorials: Getting started with Nordic's Secure...
Hi,
I'm trying to print a float over UART but I think the NRF implementation is faulty. I've tested not UART SDK example with the following changes, inserted at line 168...
I have a Thingy 91 and try to analyse the PSM and eDRX in asset tracker application. I use NCS 1.4.0 in this case.
In prj_thingy91_nrf9160ns.conf file I found the settings...
I have: nrf51822 bluetooth module, STlink V2, Keil, segger studio, nrf51 sdk and softdevice files.
I have achieved making the led blink at a ble peripheral device by nordic...
Hi,
I'm using nRF52840 with nRF5 SDK 16.0.0 and Mesh SDK 4.0.0.
I'm trying to add PB-GATT service to the ble_app_uart_coexist example. I set MESH_FEATURE_GATT_PROXY_ENABLED...
我正在执行ble_app_uart_c例程的功率测量，并且已经关闭了串行端口，这与打开串行端口时测量的波形不同。 我猜封闭的串口会影响扫描。
This is the waveform without closing the serial port
This is the waveform without serial port...
I add a compiler flag --wchar32 i n the Misc. Controls section of C/C++ to support character pointers with 32-bit width. But got errors as log attached. Any help is appreciated...
Hello guys,
I am a newbie with nrf52 and I am trying to debug ble_app_uart project under ble_peripheral directory. I do get download successful as shown in image below...
Hello,
I am trying to use the PPK (I) to measure current consumption of a DVK-BL654. I was able to successfully do this several months ago, and now when I am attempting...
Greetings,
I'm having some trouble displaying logs to the SES Debug Terminal... Basically, I can see the logs with RTTviewer but not in SES Debug Terminal. However printf...
We are in the process of applying for approvals testing of the device and need your help to confirm the following. Bluetooth data required (we use BLE4.1 mode): 1) Operating...
I need to apply for timeslot to scan private 2.4G signals, in order to save power consumption, the timeslot needs to be ended immediately after scanning the signal.
I try...
