Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
nRF5232 consuming too much power with BLE advertising interval 2 secs. I had tried using MbedOS6/OS5 and as well sleep_mode: deep sleep. Can anyone help, my appplication is...
Hello,
I have been trying to follow tutorial from:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/mesh-networks/posts/thread-tutorial-practical-guide-for-device...
Hello,
through figuring out how AWS FOTA works and following the instructions of this page
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160...
I found a couple of threads that the Windows version of the Power Profiler App in nrfConnect is broken, which it is also for me. It used to work in the past and I also like...
Hello there,
During my development I have discovered an issue with app_timer library. It is fragile for calling stop/start functions from interrupts which has higher priority...
Hi,
I have a project with nrf52832 without any BLE operation. Software runs with FreeRTOS. I am trying to add ble dfu into this project. There is a button connected to the...
Hi,
I am using nrf52832 development board with sdk 17.0.2 and softdevice 132.
I have freertos project which had ble nus service and aes cbc logic added to it.
I have...
I am trying to run the ble_app_uart from the ble_peripheral folder in the NRF SDK 15_2 I am testing with a Nordic 52840 DK (PC10040). I have made essentially no changes. ...
Hi, Nordic staff.
I'm working with Central device using S132.
There is a peripheral device using S112 in Nordic. I didn't make this peripheral.
My question is...
Hello all.
I have a question relate to: How to "ble_app_hids_keyboard" app can connect multi device?
My task: make equip peripheral base on nrf52811/840 can Adv and connect...
Hello, I am new to Nordic, I was previously using Cypress CYBT343026-01. But there were some drawbacks found during development. 1. It was consuming 315μA at 0 dBm BLE tx...
Perusing the GCC linker script supplied as part of SDK v16, I noticed that the .data section is specified as follows:
.data : AT (__etext) { __data_start__ = .; *(vtable...
I now need to burn the app firmware and modem firmware of multiple 9160 chips at the same time. Using pynrfjprog to write a program to burn the firmware for ten chips(Open...
