hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello,
I need to temporarily hardcode MBR_BOOTLOADER_ADDR address in the code so flash area is calculated correctly in fds.c. I have the following code in my ld file:
...
I'm having issue where after booting I can immediately do three SAADC samples as follows:
This works as expected where I get the callback immediately after the third call...
Hi Nordic,
I have decoded the advertise report below. Will you please confirm my understanding is correct.
Especially
[02] --> NUS_SERVICE_UUID_TYPE
[01] --> BLE_UUID_NUS_SERVICE...
Hello,
I am using the ble_app_beacon example on a nRF52840 dongle.
Without changing the code I am able to load and use it on my dongle.
Now, I am trying to add some...
Hi , i have attempted to build an spi read and write function for the BMI085 imu sensor and I seem to be having a problem with the read function. i have used the spi example...
Hi i'm studying ESB in nrf52833 DK
I have a few question.
1. When a packet is sent from ptx to prx, transaction starts, and when prx receives a packet from ptx, it sends...
Hi,
I want to add ble dfu to the hid keyboard example using nRF52810. I have tried unbonded and bonded，both are not work.
By using the bonded way, I made the following...
HI,ALL:
In SDK16, 1 .as topic,when I trigger the mouse_movement_send() and the mouse_click_send() at the same time, Error occurs.
2.how to detect BLE search device sucessfully...
Dear Members,
I tried to find a file *pca10056 project for bsc_rx on ant_plus ?
Can anyone tell me where I can find that file on the SDK ?
Thanks
Visit my lab...
We use a frontend that requires four pins and the timeslot API with our own protocol on nRF52832 & nRF52840. This works fine, but for BLE to work properly we need to leave...
i have a problem with the nRF52 DK (PCA10040) I followed these instructions https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3.1.pdf and the python version is 3.9...
Hi, I am using nRF Connect SDK 14.0 with nRF9160 DK.
I want to use nRF52840 as a controller and nRF9160 as host. To achieve this, I flashed hci_uart sample on nRF52840 and...
Hello!
I move my device from nRF52811 to nRF52820 ( QDAA-C00 ) and I have a problem when using a comparator and TWI
If I configure TWI0 or TWI1 and use it with external...
Good day,
I am using a DK board with the nRF52832 (pca10040) and I am using a 4 kHz buzzer connected to the gpio 16. I have seen the examples pwm_driver and pwm_library...
Hi, I am using the Nordic nRF52832, with the Segger IDE（Nordic）, and v1.4.0 of theSDK, and would like to know how to enable both LLPM and Multilink.
I am starting from the...
