I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,
I am new to the BLE world. I have a nrf52 DK and using softdevice 7.0.1
I am trying to to flash the basic blinky example.
In debug mode everything is fine,...
Hi, I have a custom board with an nrf52840 onboard I was able to program the nrf52, but then I executed:
% nrfjprog --eraseall
and,
% nrfjprog --pinreset
and the JLink...
According to the Zephyr documentation here the way to implement an application-specific exception handler is to define k_sys_fatal_error_handler. When I try to do this I get...
Hi. I'm doing the firmware on the custom board.
This board turns on when the button is pressed through the power button circuit. And I created the reset function using NVIC_SystemReset...
Hello, I would like to develop a simple program that sends and receives UART communication through 2 boards.
The example used "examples\peripheral\serial\pca10056\blank...
Hi, all
I'm using nrf52832 pca10040, s132..
I want to send and receive data over Tx , Rx pin.. with my custom board, cm1106 model..
<<<<<< I've connected the two devices...
Not something which I have experienced, but rather inferred from reading the code of nRF5_SDK_17.0.2_d674dde/nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend...
HI, I'm creating an IoT system, and planning to use THREAD to communicate between devices. Each device is running on a raspberry pi but I plan to use nRF52840DKs to do all...
Hi,
I am seeing a bricked device due to the fds_init() returning FDS_ERR_NO_PAGES. After some debugging, I found that all pages are marked as FDS_PAGE_DATA (no FDS_PAGE_SWAP...
Hello everybody
I hit another issue with sd_ble_gap_disconnect.
The short story is this one. I want the peripheral to initiate a disconnect if no activity for a predefined...
Hi, I'm working on an application (Zephyr) that uses nvs storage and it's been working just great for awhile (months) without any major issues. Today I noticed that when reading...
Hi to everyone!
I am using nRF52832 driven by nRF52 DK and a sensor from Maxim Integrated. As debug output i am using the RTT viewer and as IDE Keil.
The sensor comunicate...
Hi,
Recently, I purchase another nRF52840 dongle. I realised the dongle PCB was revised to 1.2.0.
Previously, I had another dongle myself that was based on PCB ver...
Hi,
I was writing a program that uses the PPI with event from the timer and the task to one of the GPIO pins. The ideal scenario is that, whenever the timer fires, it...
I am currently experimenting the the nRF52 DK and the CSCS Peripheral example.
The provided example from the SDK creates random values for cycling speed and cadence, i.e...
