I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Thanks in advanced. I update uart pin number to rx:10 and tx:9, then get the error as title described under DEBUG mode. To save power, I use uart but uarte, so I set UART_ENABLED...
Hi,
I'm using the SAADC to sample external voltage to fill in the battery service. I have use APP_TIMER_DEF to create a timer to do it every 30 seconds. Also I have init...
I'm developing a Peripheral with a rather intricate connection process and doing a lot of testing.
I find that if a Central connects, and then the Peripheral tries to send...
Hi,
I have to implement customized services in my project.I think it is better to have seperate files for service inititialization.For that purpose I have seperated service...
This (in SDK v17.0.2):
Experimental: BLE Interactive Command Line Interface Example
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ble_sdk_app_interactive.html...
Hi
I have a coupe of dongles working on a project. While validating the board, i notice a strange behavior: I have the dongles in factory reset (MBR at start, the Bootloader...
Good afternoon
i have built a small program for the uarte, using the example however im not managing to edit the event handler such that depending onthe text i recive...
Had tried to build it from the IDE before. Couldn't do it. Tried to build manually, got exactly the same error I was getting in the IDE. Parsing C:/Users/mario.raposo/zephyrproject...
Hi,
i have followed a few manuals like this one: https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/GetStarted#infotabs
or this one:
https:...
I'm trying to make an application which displays signal transferred via bluetooth.
To reduce computing time on the tablet, I want to apply oversampling in nRF52840.
The...
Thanks in advanced. I achieve 4 uint8_t dynamic sensor datas, I want 52832 transmit them through BLE continuously. Based on examples\ble_peripheral\ble_app_gatts_c, I can...
Dear,
How to evaluate a channel if is clear in property in NRF528 serials? e.g. there are ED and CCA in 802.15.4 standard, how to implement CSMA in NRF52810?
Hi
I'm using nRF52832, SDK 16.
When I enabling timer application the power consumption is increased by ~450uA, far away from the product specification
What may cause...
Hi there,
We're trying to write to the UICR CUSTOMER register to store some of the manufacturer info, such as BLE MAC address, for example.
When SD isn't running we have...
The following is loaded into flash on the nRF52840: Bootloader: 0xe0000 Application: 0x27000 SOFTDEVICE S140: 0x1000 MBR at 0x0000
Bootloader starts, waits 5 sec and runs...
