hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi everyone,
I have an issue when i am writing to flash sometimes i get a SOFTDEVICE assertion failed just after using the function fds_gc().
The structure i write...
Hi,
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/45544/nrf9160-dk-psm-current-too-high-after-opening-and-closing-a-tcp-socket/260026#260026 , however they said...
I have been looking at the Mesh library for BLE communication and wonder how much work it would be for me to use the same library for a long range 2,4 GHz radio?
Is the...
Hi,
now we use SDK17 "ble_app_hids_keyboard" example, we found after the moble phone connected to the ble keyboard, if the ble keyboard power off and power on ,the phone...
I am trying to to do adc reading from external 9V Litum battery.
In the PS document, I know nRF52832 can read adc until VDD(3.7V ???).
Then, in my case, do I have to design...
Hi,
I use the timestamp log in SDK17, and I find the time will auto clean at about 1min6-7sec.
Below is the code init the log.
/**********************************...
Hello,
I have a setup containing an NRF9160 communicating with another chip over UART at a 1M baudrate.
The following code is currently used:
I have configured the...
Hello team,
Greetings From Deepa. I need an manual installation procedure and building, compiling and Running the zephyr -OS with my laptop for learning purpose. I browsed...
I'm using nRF52840, PCA10056, and finding that if WDT is enabled (but not expired), after a soft reset (NVIC_SystemReset, or a debugger reset) the RTC no longer runs.
If...
Hi,
#define TIMEOUT_INTERVAL 2000 // Two second.
Sometimes starting app_timer_start(motTimeout_trigger_time_id, APP_TIMER_TICKS(TIMEOUT_INTERVAL), NULL), the interrupt...
Hi,
I'm wondering if I'm doing correct by following getting started guide of nRF9160 ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular...
Hello,
We start a new development in BLE and for this, we have to use the AVRCP profile.
Is this profile available with the Nordic BLE stack (SoftDevice)?
Thank you...
Hi,
my question might sound a bit silly, but I am certain that someone already faced the problem therefore I am wondering how it was addressed.
The question:
what is...
Hello, I've tried the "smp_svr" sample from the nRF Connect SDK on my new nRF52832 boards because I wanted to test Bluetooth advertising and DFU capability. They compile and...
