When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello NRF Team,
Is it possible to change the I2S buffer size on the fly while a i2s transfer is running ? (I Am using nRf52840 with SDK15.2)
I found in the documentation...
Hi, I am evaluating the nrf52832 and the Softdevice for potential use in a new product. The product has neither display nor keyboard. It therefore makes sense to use Just...
Hello,
I am quite new to developing with the nRF52840-DK. Up to this point, I have been flashing the applications (mostly the examples) over USB with the built-in J-Link...
We need to connect 2 peripherals with single central device.I have taken ble_app_multilink_central from SDK 15.3 and integrated the ble_app_uart_c in this. I am using the...
Hello,
I want to establish an UART communication with rn2483 module with nrf52-DK, SDK 15.2.0
On nrf52-DK, pins 6 and 8 are reserved for serial port, which are connected...
Hello
I used to do TWI communication until now, but it was decided to do sensor reading with SPI communication by changing the sensor.
So that's a question,
What is...
Hello,
I am wondering that when BLE5.1 SDK will be available ?
Is there any possible ways to test your BLE direction finding solution ?
As far as I know, development...
I want to set a keep alive value of MQTT while eDRX is enabled, but it doesn't work well. Any advice?
Environment - hardware: nRF9160 DK 0.8.2 - firmware: 0.7.0-29.alpha...
Hi,
I am using nRF52832 SOC along with SDK v15.2.0 with custom hardware, currently I have requirement to use DFU protocol in BLE application to get a FW of another sub system...
Hello, I hope your day is full of the scent of flowers.
I am in the process of the Ble_Cnetral and PrePhereal project.
I have added and built the Uart.
Why is...
Hi frnds,
I am using the ble_central and ble_peripheral code (nrf52840).
i am sending 400 bytes of data to central from peripheral continuously, sometimes the boards get...
3.19 [78] TIMER: High current consumption when using timer STOP task only
I'm using app_timer_stop. But I do not know how to cope with this errata. Does the timer stop that...
Hi
After upgrade modem to mfw_nrf9160_1.0.0.
Most of our SIM cards still working good on both AT and MQTT projects.
Two of our SIM cards can't connect to LTE when uses...
Hi,
I'm using nRF52840 where it's written 1.0.0 on the jlink ship and QIAAC0 on the nRF ship.
When reading the info.variant register I got 0x41414330 which is ..AAC0...
