Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Using the nrfx_qspi driver, it is possible to put a QSPI memory into DPM to save power, this all works fine and well. We want to keep the memory in DPM when uninitiating the...
Hi all,
I make a key using nrf52832. It tranfer data to other device. I have 2 option for this. Using beacon (BLE) or Enhanced ShockBurst (ESB) . I want to optimize energy...
Hi,
I was wondering what are the main differences between the different libraries included in the SDK that are meant to be implementations of ring buffers. I'm talking specifically...
Hi
I am developing a product for the health care market, and we chose embOS by Segger to by our OS for the nRF52840 Based product.
I've created a project based on ble_app_uart...
I am trying to send some data from RPi , And I am using the example of NRf Uart APP.
printf("\r\nUART example started.\r\n");
while (true) { uint8_t cr; // printf(" \r...
Hello All.
I try to build a generic function that read device reg over its I2C. I take the TWI master example of Nordic.
There is need for callback function to get in...
Hi
We are using your product nRF51x22_QFN48 with a balun BALF-NRF01E3 from ST and the PA.11 antenna from Taoglas Ltd.
Do you already have this product certified for RED...
Hi guys,
We have noticed some unexpected behavior of supervision timeout in case of few fast sequential calls of connect and disconnect commands in nRF connect app with...
hi...
i am using nrf52382 segger 15.2 version , i am facing issues i couldn't able to send the data ,here i am advertising using condition if my condition satisfied start...
Hello,
I use SDK15.2, SES4.12 and custom board with nRF52840.
I have a strip of ws2812b LED's connected to my device. I've made a simple RGB animation, each frame of which...
Hi,
I've been testing the sample code at_clent with Verizon wireless. I can send AT command to the DK via nRF Connect "LTE Link Monitor".
Q1. run AT%XCBAND=? to print...
Hi ,
I found nRF24LU1+ build in AES co-processor, but I cannot found the processing speed (the time for finish one AES processing) on datasheet.
Because my customer...
Hi,
I know this is a stupid question, but I couldn't find any answer in the forum or anywhere, and it is getting annoying :)
I'm using SEGGER Embedded Studio for ARM ...
