Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi.
I have an experience that I do not understand.
<main>
<timer handler>
"PushSwitch" changed to true when the button was pressed using a switch interrupt...
Dear nordic,
I have a custom board. first time its working fine and i flash the program without any issue. after few days i started to reflash the chip its show some errors...
Hi,
From last couple of months I'm working on NRF52840 chip and designed a battery operated device. I also made 5 prototype boards and I'm happy with the range test, coded...
I see two different issue from Segger ES. The below piece of code work well in debug mode, comparison of array at 2k and it fails at release mode. Wondering what's happening...
As a brief introduction, our research group uses bluetooth advertising to broadcast commands and responses between end devices and 'routers' which are connected to a PC. ...
Hi,
BLE Application on nRF52840 (pca10056) development board is being developed.
Application stopped the advertising to make device non-discoverable.
After that trying...
SDK 15.2, API 6.1
I have 1 firmware and 2 PCB it operates. PCB A was an external crystal and the sdk_config file is setup for the operation. However, PCB B uses internal...
I would like to communicate with and existing product that has the ability to communicate thanks to a UART-Bluetooth module. This module uses a Serial Port Profile and shows...
Hi,
I'm working on a thread network and I have some difficulties to configure the BorderRouter.
I use the BorderRouter V2 rapsberry image from Nordic, I recompile the...
Hi,
I want to be able to update the bootloader along with the application via OTA DFU. I know I can't generate both the application and bootloader in one image/zip so I...
I am looking for specs for the input impedance of the comparators (COMP and LPCOMP) for the nRF52832. I searched the forum and all I found was someone saying it is ">1 Mohm...
Hi,
I am trying to incorporate flash storage library to ble_app_uart_c example. I have added all necessary functions from ...\examples\peripheral\flash_fstorage.
When...
Hi everybody
I have a couple of questions regarding power consumption for the 'nRF5_SDK_11.0.0_89a8197' (nRF52832).
I currently have an application which use 12-bit SAADC...
Hi, I made a simple diagram of what my device should do:
The nRF52840 should receive data via SPI from another controller, mathematically process this data, and output...
Hi,
I just pulled the source code of 'nrf' from the git server (SHA1 ID: 383da27cc232bd7baa353e965b7fe8fa08b56d77).
After performed 'west update' to sync other repos,...
