Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello everyone, I want to know and how, if it is possible, to hide UUID Beacon string during the advertising mode.
My goal is to not show the UUID by any sniffer, like Master...
Dear All,
I‘m going nuts while working on the basically really simpe task of reading ADC voltages on GPIO (AIN3) between 0 and 1.25V.
The voltage should fit well in...
Hi all,
At Peripheral end, I will get an callback "BLE_GATTS_EVT_WRITE" whenever I do a write on charcteristic write value from Mobile App.
Can you please point me to...
Hi all,
I use nrf52 for continuous receiving when enabling the shortcut of END_START.We know when the shortcut of END_START is enabled,the radio start task is triggered...
Hi guys.
I'm using the nRF Mesh LED example and I'm using my Android/iOS phone as a provisioner. After provisioning, I was curious whether the phone can visually represent...
hi...
i am using latest sdk 3.1 mesh ,nRF52832 development kit while i am building it showing error "boards.h no such directory found ", even tools are set .how to solve...
Hallo everybody,
In or project we have an energy harvesting circuit. Because of this energy harvesting from an piezo we don`t have enough power to charge all supporting...
hi,could i ask you what should i do in order to use ant on the pca10056 board? i added the s340 softdevice but no example works on the board. thanks a lot!!
I am working on a MQTT related application on nRF9160 DK, and grabbed mqtt_simple as a baseline for development. All of my libraries are back at the last tagged releases:...
Hi, I'm confused, according to Bluetooth 4.0 Specification bytes are send in Little Endian byte order, and with LSB first in every byte. So when I receive raw data from characteristic...
When running "pip install nrfutil" I get this message - "Could not find a version that satisfies the requirement antlib~=1.0b (from nrfutil) (from versions: ) No matching...
Hi all,
In Nordic SDK ble_app_gls Example , the following UUID is added as part of Advertisement packet
static ble_uuid_t m_adv_uuids[] = /**< Universally unique service...
Hello,
I'm currently building a project for the nRF52 (using SDK 15.2). I need to have 2 ADC channels, 1 for temperature sensor and 1 for battery level. I figured that I...
I want to let nRF9160 communicate through UART with 3.3V logic level, but the logic level is originally 1.8V.
I have been reading nRF91_DK_User_Guide_v07.pdf, but I'm not...
