Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I am using 15.2.0 SDK and 3.0.0 Mesh SDK for developing the nRF Mesh.
I am using segger IDE for programming but I am looking for a way to program the device with hex...
Hi
In MESH 3.10 SDK，i want to configure and use virtual address, but i can't add the virtual address in both pulication address/subscription address when i use NRF Mesh...
Hi Sir,
Normally, the printf() may show the message to UART_0, is there any way we can re-direct the message of printf() to UART_1?
in other words, can we choose the...
I am facing issues in debugging ble_app_uart program available in nRF5 SDK. I am trying to debug it on IAR workbench using Jlink PLUS debugger in SWD mode.
I could connect...
Hi Nordic support team,
I used mergehex to merge the hex files of Softdevice, Secure Bootloader (nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_ble) and...
Hey
I am working on mesh networking (light switch program). I would like to make a connection between client and server without involving provisioner based on the RSSI value...
Hi,
I specially bought more than 20 nrf52832 modules, and I want to build a bluetooth network (star network) for one-to-many communication. We have an application that requires...
Hi all,
I have an issue when trying to use the fstorage without the SoftDevice. The documentation explains that it is possible to use the FStorage without SoftDevice if...
Hello,
I have nrf52832 development board with PCA10040 version 1.1.1. I can build my code correctly and I can erase my chip from Keil uvision but when I try to download...
Hi,
I am trying to interface OLED(SSD1306 driver) module/break-out with nRF52840 D.K, PCA10056 1.0.0 but it's showing some noise/dots/garbage. Code: nRF5_SDK_15.2.0_9412b96...
Hi all. I want to add ssd1306 controlled OLED display with SPI to my project how i can hook up u8g2 library or another library for OLED display to nRF52832.
My application requires ultra-low power consumption, hence the nRF52810 will operate in low power - RTC running from LFRC clock, full RAM retention (1.5uA current spec'd)...
Hi,
I really would like to be able interface with the modem at the lowest possible level. I got the bsdlib working.
I use the following procedure to send AT commands and...
Hi Nordic,
We are having a Finger Wearable Unit(FWU) based on nRF52832.We are using JLINK Base Debugger to debug the FWU.We are able to debug and get the debug logs when...
