hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
We are evaluating the nRF54LM20B for an embedded audio classification application and are trying to determine whether the Axon NPU can meet our latency and energy targets...
Hello,
I encountered an issue when using BT_LE_ADV_OPT_CODED in the bt_le_adv_param options.
When I enable BT_LE_ADV_OPT_CODED , the device cannot be scanned by other...
I am currently developing a project using an nRF5340DK and a custom board. ---------------------------------------------
PC ---(SWD)--- IntMCU at nRF5340DK ---(SWD)--- nRF5340...
Hi,
We are trying to get an accurate estimation of energy consumption of LTE searches and data sessions.
We currently do this based on XMODEMSLEEP and CSCON notifications...
I'm a bit confused about configuration necessary for PAwR where a connection is initiated with AUX_CONNECT_REQ as in examples periodic_adv_conn/periodic_sync_conn. If I disable...
Hi, I’m seeing a build failure after enabling SQSPI in the device tree when building with MCUBoot on NCS v3.2.1 for nRF54L15. The build works fine without SQSPI, but once...
Hello,
Did anyone get nrf54L15 to work with a TFT display over SPI?
I have been using the 1.28" 240x240 gc9a01 in several projects with nrf52840 (both using the DK...
Hello,
Recently I designed a wireless keyboard with a nRF52840 as the main processor. I had the board reviewed by a friend and had it produced by JLCPCB. I have assembled...
I'm currently attempting to profile a non-rechargeable lithium battery on nPM PowerUP(2.2.3). When I start the profiling process, the charging stage is correctly skipped,...
We've designed our own board based on nRF9160 for main CPU w/ LTE and an nRF52 for BLE. Using BMP for debugging.
I've successfully run several boards through the production...
hi,
i'm learning this exercise and i got this build error.
i'm using nrf 9160dk so can anyone tell me what problem am i facing in build time error.
thanks
vivek
Not sure if this is an nRF Connect or VS Code or Zephyr or West or some combination of the above, but I'd like to configure the development environment (nRF Connect extension...
Hello Nordic,
I am currently evaluating the nPM2100 using the nPM2100 Evaluation Kit for a low-power embedded device powered by a CR123A primary lithium battery (Li-MnO...
Hi,
I am testing an eSIM card. I am able to read the ICCID (20 digits) using the following command:
AT%XICCID %XICCID: 8934014012215261620 OK
However, I don’t know how...
