When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hello,
I'm using SDK 13.0.0.1 to develop my project. For driver example, such as RTC, I can't see data log while I can see the data log for BLE example, such as ble_app_uart...
Hi @ all,
We discovered a bug in the Nordic TLS API, which only appears once a secure TCP connection that makes use of certificates is to be established.
The provided...
Hello All,
I'm developing a BLE sensor based on the nRF52832 which needs to do the following:
Use an (i)Beacon for the user to find the sensor with an App on a mobile...
nRF52832 has errata about gpiote as below.
3.29 [97] GPIOTE: High current consumption in System ON Idle mode
So I want to use PORT event for gpio interrupt, but PORT...
Hi all,
I programed hex file (blinky example) to nRF51DK via nRFgo Studio, and the board could work fine (keep blinky).
However, the nRF51DK will work FAIL (LEDs are not...
Hi,
I need to monitor voltage very frequently, have access to the latest value and also to have interrupt on low limit.
But I do not want to have interrupt on EVT_DONE,...
Does anybody knows exact number of the "4 SIG fixed group addresses"?
Is it 0x00? or other?
In the SIG document, there is below chapter.
Group Addresses
A Group...
Hello Sir,
I have developed a product on nRF52832 DK kit and using S132 soft device. I want to flash this same hex file into SparkFun nRF52832 using nRF52832 DK. But i...
I'd like to use nrfjprog to read contents of QSPI external memory. (I'm using an nRF52840-QIAA on a custom PCB, based on the PDK.)
Using application firmware I am able...
Hello
i am using nrf52840 dk with sdk 13.0r3 software.
on first board, using example ble_app_hrs_rscs_relay example.
on second board, using example ble_app_hrs_peripheral...
Hi,
On my single I2C Bus, I have interfaced 4 I2C slave devices.. Now my voltage level of this bus behaves randomly. sometimes It shows 3.3V, but most of the times It stays...
Hi all,
We are currently under FCC certification testing for our custom BLE module based on nRF51822 but failed with the average power exceeding the limit. Nordic Semiconductor...
I'm following the tutorial Development with GCC and Eclipse, but have problem when use GCC to compile project that use PWM library.
I found that when compile the code with...
