When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
In the schematic presented in the topic 17.1 (dc/dc converter, image below) of the nRF8001 datasheet it isn't shown that AVDD should be connect to a power supply as...
devzone.nordicsemi.com/.../
In this blog this is written:
"Opening and closing a connection event adds a lot of overhead"
how much is the overhead and where can i...
Hello,
I am currently developing a new bt-le-program and besides my own log-messages, I wanted to enable also the log-output that is happing in the files from the Nordic...
I'm building something based on ble_app_gls. However, I only want it to be pairable when I say so (user presses a button to put it into that mode). Is there a "correct" way...
Hi,
upon connection I get these messages via RTT:
nrf_ble_gatt:DEBUG:Peer on connection 0x0 requested an ATT MTU of 185 bytes.
nrf_ble_gatt:DEBUG:Updating ATT MTU to...
I would like to know how to dampen the effect of metal surface on BLE signal . Let me give you an instance, i am installing a wireless sensor inside a metal box and this sensor...
Hi,
I'm trying to make github.com/.../nrf52-spi-i2c-master-ssd1306 to compile with GCC (linux). So far I've managed to get it compiled, but linking fails:
mkdir _build...
Hi all,
I am using NRF51822 Bluetooth, which I am interfacing with the my microcontroller UART. when I dump the code into my Nordic NRF51822 BLE then it is only advertising...
Hi all, I have an Eclipse project in which I want to transfer packets of data bidirectionally between ESB and UART. The makefile includes both nrf_esb.c and app_timer.c (needed...
I'm working on a 2.4GHz wireless microphone (2T1R) project now. I'm wondering can I use nRF24L01+ as the core of transmitter and receiver? Also can it be configured into 2T1R...
So the question would be if I would need to pair each time the device comes out of reset or are there information stored to return to direct communication without pairing...
The chip uses nRF 52832. MDK keil μVision V 5.22.0.0 is used as the development environment.
The SDK version uses 13.0.0_04a 0 bfd.It is based on template_project.
1drv...
hi,
i have two nrf51822 beacons in which one would send data to other over ble.how can i make nrf51822 as central.what are the modifications should i do to make it central...
hello,
i want to know that which code i have to prefer for communication of nrf51822 with android phone via bluetooth.suggest me the code for using bluetooth of nrf51822...
Hi,
I expected a bit more fanfare for the BLE-based DFU, but eventually found it in the 4.4 SDK after my sales rep told me it was there ;)
Some questions:
(1) Is...
