Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi, I'm trying to run ble peripheral and timeslot receiver at the same time. I can see ble advertisements and I can connect to the peripheral. I can also read and write ble...
Hi,
Some questions below about the HID keyboard that refer to the example "/s110/ble_app_hids_keyboard" .
What initialize m_advertising_mode value before to call...
Hello,
to reduce ernergy consumption i use the sd_app_evt_wait() function while the twi is sending or receiving data.
i set nrf_twi->address and nrf_twi->txd and set...
Hello,
I have troubles using spi_master_example.
I want to control by spi a slave device from the nRF, I am sending sequences as expected and my slave device answers me...
The S130 SDS 0.5 documents a CODE_R1_BASE of 0x00020000, but I can't get it to work with code at this location. Any SoftDevice API call ends up in the application's SVC_Handler...
Hi,
i use the library app_gpiote to setup interrupts on a toggling external pin(this pin generates a signal which changes from high to low).The external interrupt signal...
Links: ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection，I don't Know how it works.The ble device call disconnection,but ble android phone respones it more then 5s...
Hi, I'm a student at Oregon State University using the nRF51 Development Kit for a project. I can't seem to find any functions for sending and recieving Bluetooth signals...
HI ALL!
I got a question about establishing my own service.
Currently, I can just send my data through the 'hrs' service(by replacing the heart_rate value with my own...
Hi,
I just downloaded the Utility app for the ble apps(nRF518 SDK) checking on my i5 at iOS 7.1.2. I have tried to connect the apps(hr, proximity) of Utility, but there is...
I changed the dfu start address to 0x00 and application start address to 0x8000.
The application use the RTC0 IRQ to count the timer,
but the RTC0 IRQ did not work correct...
I've been successfully using IAR and I-jet with the 51822 and S110. I can build, download and run under the debugger with no problems.
I recently switched to the 51422...
Has anyone has any success flashing a nRF24LU+ dongle NOT using the official dev kit ? I'm attempting to flash using another microcontroller programmed as an SPI Master so...
I will be happy if someone points out this is a newbie problem and not something weirder...
Running on Win7, 64 bit BTW...
I recently received the nRF51 eval kit. I...
