I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello everyone!
I'm currently developing a project in which I require a remote control (touchscreen TFT + arm MCU) to send and recive some data over a bluetooth connection...
Hallo
We want to update the firmware over the air (BLE).
What is a safty concept?
Our firmware need about 60KB flash ROM.
What have we to calculate for BLE software?
...
Hello Everybody,
I have a question about nRF51422. I want to monitor the ANT+ message from any sensor, which is already connected with the device,
Scenario : if it is...
Hello,
Im trying to create a synchronisation method for sensors using BLE. At the moment i can synchronise them within 10ms accuracy, in theory it should be within 2ms...
Dear all:
same as this issue:
devzone.nordicsemi.com/.../use-dfu-to-update-ap-over-ble-single-bank
it seem same as my way that modify modify "dfu_dual_bank_ble" target...
A big update this week for our S110 SoftDevice. Full OTA DFU for SoftDevice and Application. Also Multi-acivity concurrency for Bluetooth Smart and 2.4GHz protocols. As Developers...
Hello
I got my nRF51422 DK, and got few inquiries
For ANT,BLE DK, where can i find API documentation?
BLE can be implement on nRF51422 DK?
Is there sample project...
I have a 'fresh' nRF51822 on a board and it's not clear to me what procedure I need to follow in order to get it to work. I'm using the Segger programmer and I can program...
In the Keil debug interface, how can I find if the application is throwing an ASSERT, and which it is? I'm using the S110 softdevice. (See other question for context devzone...
Hello, I have a weird problem, the nRF24L01+ is sending a TX PAYLOAD that was left in the TX FIFO (clocked with W_TX_PAYLOAD) as an ACK PAYLOAD when switching to PRX mode...
hello everyone,
i am trying to use SDA and SCL pins of TWI other than 24 and 25, is it possible? i want to know before using other pins for twi other than 24 nd 25 with...
Hi
I try to communicate with others TWi devices using the twi_hw_master driver.
When i initiate a communication with twi_master_transfer , i don't receive any ack from...
Hi,
I have purchased the nRF8001 Development Kit and so far I wired the nRF2740 board to a FTDI VNC2 microcontroller. I have been reading about how to configure the 8001...
Hello. I'm trying to port the ble_hrs to a custom board with an NRF51822 on it, but the advertising never starts. While I'm debugging this, what should I be looking out for...