Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
Hi
im develop my product base nrfdesktop of ncs,i build the project and program to the nrf52840DK，it can run and perform funcation.but when i program it to my board,it cant...
This is a continuation of the following ticket: The resolution was logged as DRGN-19197, which was part of v2.4.0 , but did not resolved the issue.
I have created a minimal...
Hello,
Using the sample PSA Protected Storage on the nrf5340 DK with NCS v2.6.1 (and v2.5.2). My prj.conf contains these settings:
I flash the sample provisioning_image...
Hi,
I am using Nordic nRF52833 as a peripheral which uses mcuboot and DFU over BLE. I can easily upgrade firmware on that device by connecting to it with nRF Connect mobile...
Hi,
I use nrf52833 Development board PCA10100 to do loss test as peripheral and speed is 1Mbps, tx power is MAX. It's loss rate is very high, when nrf52833 sends a packet...
Hi, I am trying to use the periodic advertising connection examples and get Hci errors: opcode 0x2036 status 0x01 Failed to create advertising set (err -5)
I am on NCS 2...
Hi:
I checked the zephyr.dts file, but I couldn't find the addresses for interrupt-controller(0x e000e100 ) , timer(0x e000e010) , and memory(0x20000000) in the nRF9160...
Hello, I'm experiencing an issue with communication between the nRF52840 and nRF9160 on the Thingy platform using the connectivity bridge. I successfully established communication...
Support,
Due to the limitations described in the referenced previous ticket, I am unable to successfully discover a service and its characteristics because of a hard fault...
I am struggling with the same requirement as this ticket :
ie receive from a UARTE without knowing in advance how many rx bytes to expect. This is typical for exchanging...
I'm running the nrf5340_audio application on the nRF5340 Audio DK and have a UART wired to TP60 and TP61. As long as I have USB (onboard j-link) or my Segger j-link connected...
We used to specify BOARD and BOARD_ROOT at the cmake level, but so far attempts to do the same using sysbuild did not succeeded. Is it still possible or should we rely on...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1024, please.
It is not very clear by reading the assembly code...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1050, please.
It is not very clear by reading the assembly code...
Recently the source control icon (git extension) in the activity bar in vs code shows more than changes in code.
As can be seen here the icon adds up the changes in...
