I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hello,
I'm trying to get a TIMER triggered ADC read on P1.11 AIN4. Sample advanced_non_blocking_internal_timer sounds like what I want but it isn't NRF54L15 compatible...
I am designing a very-low-cost device based on the nRF9151 and would like a quick technical clarification.
My plan is to power the SoC and all GPIO rails from a single 3...
I'm working on a project were we require the use of a custom OOB key (not generated by the device itself) and LESC.
We have both the central and peripheral device to configure...
Hi ,
Our nRF52840 chip is drawing a high-current burst of about 1.5 seconds during the DFU upgrade. Because we have a 10 mA current limit on the battery, the system browns...
Hi
According to the errata at https://docs-be.nordicsemi.com/bundle/errata_nRF21540_Rev2/attach/nRF21540_Revision_2_Errata_v1.2.pdf?_LANG=enus, a 33k resistor is required...
Hi,
I'm using nrf52840 in revision 3, which has protection access port enabled by default.
My application is built with SDK15.0.0 / SDS S140 6.0.0
In order to get debug...
Hi,
I would like to receive notifications from iPhone to nRF54L15-DK over BLE. Anyone in the nRF community tried iOS notifications over BLE to tell me how it is done please...
Hello,
Current Situation
We are working with an nRF5340 device running nRF Connect SDK v2.7.99-cs2 . BLE security is configured for Just Works pairing (Security Mode 1...
Dear Nordic Team,
I am using NRF54L15 on NRF54 DK board and when trying to use/activate any other UART other than UART20 (e.g. UART21, UART22, UART00) on my project, every...
Hello, I've been developing an nRF52840 on a custom PCB for ~1 month now, and my environment was working previously. After updating my version of Jlink and installing other...
Hello.
I'm using nrf9151 with nRF Connect SDK v3.1.1 and Zephyr v4.1.99, modem firmware v2.0.2 I try to implement the full modem update. After downloading the "firmware...
Hello,
I can no longer use AT commands on my nRF9161 DK development board.
It used to work perfectly, but I don't know what happened.
I had previously completed the...
Hello,
I wanted to see if it is possible to move provisioned devices between team IDs in the NRF cloud. Right now I am using a nrf9151 to connect to the cloud. Once the...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board.
My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
