Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi!
How do you recommend to debug crashes?
Especially how do you recommend to debug crashes that happen to our customers that we cannot reproduce?
So far I have been...
In order to develop the most effective power supply possible for the nRF9160 SIP, I need to know both the maximum current consumption of the nRF9160 and its duration.
The...
I’m using nRF Connect SDK v2.8.0 and working on BLE OTA (DFU) for the nRF7002 DK . I followed the Nordic “DFU with external flash” exercise and integrated it into the Wi-Fi...
Hi,
I'm in the process of porting our existing nrf5 project to nrfConnect SDK bare metal and am struggling to port our QSPI display driver. Are there any plans to add support...
Hello team,
I am working on a Direction Finding (AoA) setup using nRF5340 DK as a CTE Transmitter (Tag) and a Silicon Labs BRD4185A (AoA board) as the Anchor/Receiver. ...
We have developed device that used 2.6 and when moving to 2.9 everything broke apart and I cant get it to boot and I cant get any output from device. Be it from USB or SWD...
I am having a persistent issue with the ANT+ examples in the nRF5 SDK on an nRF52832 DK PCA10040. The application firmware compiles and runs correctly, but the ANT+ signal...
Dear Matter Support Team,
I have a setup where an On/Off Switch device is successfully bound to a Light device in our Matter network.
I would like to know which specific...
I am using the Ublox NORA-B206 module and facing issues with the debug option in the VS Code extension. The debugger fails to start, and I receive the following error message...
Hi Team,
We have a custom board with nRF9151 SoC that shows complete RF failure. The modem initializes correctly and detects the SIM card, but cannot detect any RF signal...
I'm adjusting my program with nrf52832 and nrf5SDK.
I attempted to use the parameter PM_PEER_ID_N_AVAILABLE_IDS to control the upper limit of the bound users.
However...
Hello, I am testing the power consumption of the npm1304 for the first time. To do this, I am using the PPK2 connected to the nPM1304-EK on VBAT and GND of the P1 connector...
Hello, According to the nRF7000 specification, the sleep current should be around 15 µA. Electrical specification .
We have a custom PCB with nRF9160 + nRF7000, and the...
Hello DevZone,
I'm testing the Matter OTA by using OTA provider. Referring to: Performing Device Firmware Upgrade in the nRF Connect examples
But it's too slow. Is that...
I want to update 52840DK FW using Matter OTA, but I have not found SOP, could you tell me how to operate?
BTW, I use Raspberry Pi4 connected with RCP as border router. ...
