Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I'm trying to send I2S data (~ 16 kHz, 24 bits) via BLE using the nRF52 DK and the nRF5 SDK 17.1.0. After I get the data from the I2S driver (by specification, they...
Hi!
To measure the voltage level of a coin cell CR2450 can be done in different ways.
You can use the comparator, the low power comparator or the ADC.
I wonder which...
Hi, The getaddrinfo() function returns the same IP address for www2.domain.com and domain.com, namely that of domain.com while they are running on different servers and have...
Hi
I am currently working on a Matter project.
I configured OTBR with Raspberry Pi, completed pairing with nRF52840 board (Light bulb), and confirmed that Light on/off...
Hi,
In order to make firmware updates over Bluetooth work, I need to enable the MCU boot loader. Is use CONFIG_BOOTLOADER_MCUBOOT=y in my prj.conf file to enable it. My...
I'm doing with the nRF Connect SDK v.19.1, testing the project C:\ncs\v1.9.1\zephyr\samples\hello_world.
The main. c file is
void main(void) { printk("Hello World! %s...
Hi， i'm use latest ncs develop bluetooth extend advertising, and i'm try use west build -t menuconfig to config scan filter config
such as BT_CTLR_DUP_FILTER_LEN or BT_CTLR_DUP_FILTER_ADV_SET_MAX...
I want to define config values in an optional overlay that is enabled after writing to a custom service/characteristic using NCS. Based on this https://devzone.nordicsemi...
Hi,
in my company, we are using an nRF9160 on a custom board. Recently we updated from NCS 1.8.0 to 2.0.2 (we also still use spm for now).
1.8.0 was already not super...
Hello all, Ive combed through the NRF52840 datasheet and the BMD341 datasheet, and SDK examples attempting to determine if through software (and possible hardware change)...
Hello,
in our application we want to use a simple serial Spi Flash: M25P40 (only 1 data signal).
For evaluationI I connected this Spi Flash to the nrf5340-DK Board:
...
Hi
I want to implement function of scheduler server model with Timer server model, I checked the nRF Connect SDK, but I still did not understand,
Could you give some advices...
Hey Nordic,
Currently, I am working on a project based on "ble_app_uart" and "ble_app_uart_c". You can download the projects below:
Central (nRF52833-DK):
Peripheral...
Hi everyone,
I am in the process of programming a DFU via UART. I currently have in memory only the softdevice including the MBR and the bootloader. If I enter in nrfutil...
