Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
I am trying to add SoftDevice to our project which was non-SD for a year now, but I'm stuck with a problem.
I know that there are separate files for nrf_error.h...
In order to simply the creation of nRF softdevice projects, I'd like to make a suggestion. Rather than require the end-programmer to include dozens of individual include paths...
i changed the net-core flash partition and saved it to pm_static.yml. everything is ok while i build multi-image(mcuboot, cpuapp, b0n, cpunet) until my partner wants to build...
hello Nordic
i am working with nrf52840, zephyr rtos.
i can preform dfu via mcumgr cli (command line interface) or via nrfConnect application on my cell phone.
however...
Hi,
we are trying to use waveshare 2.9 epaper display with nrf52832, converted stm32 sample code to nrf52 with no luck. It seems we can not send command and data correctly...
Hi team ,
I am using 15.3 sdk and NRF52832 hardware. and Tool - SEGGER Embedded Studio for ARM 4.30c
I have developed code with DFU feature and and generated .hex file...
Hi,
I want to disable the UART of MCUBOOT to reduce power consumption. I searched in the DevZone and got the answer as below.
I followed the answer above, and created...
Hi there,
For the nRF5340, I read it support the Zigbee . So I just wanna know does it support the Zigbee frequency band in China, which is 780M?
Thanks,
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I know there is the following documentation. ・ SEGGER Embedded Studio Reference Manual : https://studio.segger...
Dear all
I'm using the SD s140 and nRF52840 along with one of the latest SDKs (17...). Everything works fine, I'm able to start advertising and connect, but from time to...
As the title says,
I combined the TWI function with the ble_app_uart example and the three i2c sensor communication was successful.
However, when I added SPI to develop...
Hello, I'm new to nRF Connect SDK.
I managed to add the blinky example to build. I added a custom board.
There is a prf.conf project file with just CONFIG_GPIO=y I'm now...
I'm trying to get the device ID of the lis3dh accelerometer on a Thingy:52
nrf_drv_twi_tx returns 3 as an error. This means NRF_ERROR_INTERNAL --> "If an error was detected...
Hello, when i try to flash my card, (nrf52840) in visual studio code i have those errors
ERROR: The file specified is not a valid hex file, has data outside valid areas...
I am trying to build an application that can switch into MCUBoot's serial recovery mode and receive a new firmware image over the serial port. I'm using NCS 1.7.1 through...
