Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I want to run my application on the latest open thread libraries.
As per the page "infocenter.nordicsemi.com/.../thread_ot_libraries_building.html"
we need to run...
Hi,
We are using the nRF52840 Dev Kit with SDK17 and SD140 without FreeRTOS. There has been discussion in other postings <link> about increased current consumption caused...
Hi,
I am having a NRF9160DK board , which i want to use it for an simplest BLE application which sends the data from NRF52840 to my mobile using a simple BLE application...
Dear sir/madame
In our project we want to implement MAX17260 battery fuel gauge to monitor the battery status in the handheld device.
The interface towards MAX17260 is...
I'm trying to run the HID composite example on a nRF52840 dongle, and its not working:
- I refer to : nRF5_SDK_17.0.2_d674dde\examples\peripheral\usbd_hid_composite\pca10056...
Looks like 2 mistake in the latest nRF9160 production specification:
1: 1Mbps but 1200 in description section.
2: Power consumption could be in uA instead of mA.
Hello,
Sorry for the basic question, but I am trying to customize an application basing on the ble_app_cgms example.
In the debugger terminal on SES I am receiving the...
Hello,
I am currently working on an IIoT product using Zephyr and NRF SDK v1.5.1-2-g76c027893 on the NRF9160 and a WFM200 wifi chip. For this project we are using Civetweb...
Hi
I'm locking for an example like zephyr\samples\boards\nrf\system_off for nRF9160 DK
zephyr\samples\boards\nrf\system_off uses nRF51 DK or nRF52 DK board for the demo...
Dear support team,
I would like to use GPIO 09/10 as a GPIO interrupt.
I just searched and I see that need to define CONFIG_NFCT_PINS_AS_GPIOS.
But I can't do it. Please...
Hello, I'm making a system with NUS of nRF52832 and nRF52840 to sample data with SAADC. I started the system with "ble_app_uart__saadc_timer_driven__scan_mode_03" from Github...
Hello!
There is a sample simple_mqtt which is written for nrf9160 DK. Is it possible to make app_signed.hex file to load in thingy 91.
I tried to change prj.conf and have...
Hi,
Using the HRS peripheral example provided in SDK17 with S140 7.2.0, I am in the process of migrating to a custom board using nRF52833. I have already made some changes...
Hi,
Can you please tell me if Segger compiler initializes all variables to default values?
If so - can you please send me a link to that content?
Thanks
Hello,
My nRF52840 board is connected with SPI flash over SPI. I have configured the nordic as master and my SPI flash is slave as mentioned below:
Using the internal...
