Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello!
i´m enable ble long range like central for scanner beacons, i can see long range beacons, but only one time, then i need to restart my DK: i use to do this ble_uart_c...
Hello,
As per your given link in 1.2 Build and flash - using SEGGER Embedded Studio ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts...
Hi,
It appears that at least one Mesh_v4.2.0 example (light switch) will not link under nRF5_SDK_17.0.2.
I managed to get Mesh examples to run under SDK_17.0.0 a while...
I have a new Bluetooth remote product in development that has a bluetooth stack that will incorporate HID, BAS, NUS, ANCS, and buttonless DFU services. I have the HID and...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm getting this error while trying to connect with my device in the "ble_app_hrs_c".
"Connection...
I have found a few "how to" on cofiguring Eclipse for application development on nRF52 devices. After some point things are not as described in this guides. So, Is there any...
I'm trying to create a read event whenever a certain characteristic is read. I used BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event to monitor that. I also set "is_defered_read"...
Hello,
I am developing a composite HID peripheral based on the nRF52840 that can connect to a PC either via USB or BLE.
I am using SDK 15.0.0.
Regardless of the connection...
When I build and run an example Bluetooth: Peripheral HIDS keyboard (it's the same for master branch and v1.3.2) using nRF52840 DK I faced one strange behaviour. To simplify...
I just downloaded the latest version of the pc-ble-driver hoping some of the bugs I had reported were fixed. The downside is the notes do NOT indicate they were addressed...
I'm working on an nRF52840 design where we may get away with only the outer pin row on the package.
However, one pin on the inner row of harder to reach pins seems important...
To the kind attention of Nordic support team,
I'm considering here a scenario where only a device and only an host PC are involved. They are ble bonded together.
Now,...
I have been working on receiving data from sensor using nrf52832 and I have been successful in getting the data and printing the same in the app. I have also been succesful...
Hi!
I am using an ASXL375 accelerometer with a nRF52832, and I am trying to figure out a good way to read the sensor data asynchronously (allowing the other processes the...
Hi,
I am using SDK 16 and nrf52810 pca10040e. I tried to build the example code for nrf52810 bootloader from the nordic example folder(examples/dfu/secure_bootloader/pca10040es112_ble...
