Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi,
I am using nrf52840 module with a kit that i built by myself. The kit is working because i am able to flash and debug without problems.
I am using Segger embedded...
Hi,
Is it possible to advertize and scan only on the 2M PHY and w/o using at all the 1M PHY on nRF52840/S140 system ?
The actual system is running fine if we use the 1M...
Good day!
I purchased the nRF24L01 Evolution Kit, but:
1. The driver and software that comes with the board, only under Windows XP. Are there drivers and software for...
Sorry in advance if this is an FAQ or maybe two
Situation is this - for regulatory reasons, production/release software here is built using a known version of arm-gcc, and...
I'm using scannig with whitelist on nRF52840 Dongle SDK V15.2 (usbd_ble_uart_freertos example)
when BLE_GAP_EVT_ADV_REPORT is called scanning stops, So it can scan just...
I am working on matching an antenna to the nrf52832 QFN package. I am looking at the reference design, which has a 30 mil wide trace. I believe that is supposed to be 50 ohms...
I have an application (key fob) that needs to wake up on a button press. Scan and connect to a specific BLE device, then send one byte of data and disconnect and turn off...
Hello, I have a question about using PPI with a SPI transfer.
I’m using a NRF52832 custom board with the Softdevice. I’m reading sensor data every 20ms via TWI and sampling...
Good day!
I purchased the nRF24L01 Evolution Kit, but:
1. The driver and software that comes with the board, only under Windows XP. Are there drivers and software for...
Hi,
I use the server and client from "light_switch DEMO", along with iOS app (nRF Mesh) for setting and pairing. Both ”subscription” & ”publish address” are set as 0xC001...
Hi,
Serialization Function packet format for nRF5 SDK v15.2.0
Am working on serialization where we have already developed code using nRF5 SDK v11.0.0 but now we started...
Hi
I have a problem with receiving / transmitting a packet of characteristics with a descriptor 2902 (CCCD 2902). The principle of operation of my program is that the device...
What will be correct linker script changes for nrf51802 device using soft device ble application
I made changes in RAM start and SIZE. found in open source forum,
MEMORY...
I using 3 nRF52840 DK borads (provisioner,light_switch_client, DFU). I set DFU (DFU example used) as target board and connected it to PC as serial interface. I have provisioned...
